43
EN
Introduction Connections
Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording FunctionsIntroduction Connections
Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording
1) Go to the dubbing list, then select a title using
[K \ L]. Then press [ENTER\OK].
2) Select “Move” using [K \ L], then press
[ENTER\OK].
3) Select a desired insert point using [K \ L], then
press [ENTER\OK].
1) Select “Delete All” in the dubbing menu using
[K \ L], then press [ENTER\OK].
2) Select “Yes” using [K \ L], then press
[ENTER\OK]. Final confirmation message will
appear.
3) Select “Yes” using [K \ L], then press
[ENTER\OK].
• To go back and forth between dubbing menu and
dubbing list, use [0 \ 1].
7 After adding all the titles you want, select
“Dubbing Start” in the dubbing menu using
[K \ L], then press [ENTER\OK].
8 Select a desired recording mode using [0 \ 1],
then press [ENTER\OK].
e.g.) HDD A DVD
Confirmation message will appear.
• Depending on the dubbing direction, the available
recording mode varies.
• When dubbing from HDD to DVD, you can select “High”
to perform the high speed dubbing (refer to “Recording
Mode for Dubbing” on page 41 for more details).
9 Select “Yes” using [K \ L], then press
[ENTER\OK].
If dubbing continues when timer recording starts, the next
display will appear.
Dubbing will start.
• It may take awhile to prepare for the dubbing.
To stop the dubbing in progress:
Press [C STOP] on the front panel.
Press [STOP C] for 2 seconds on the remote control.
Note
• Dubbing will be cancelled 2 minutes before starting timer
recording.
Setting a Disc to Protect
To prevent accidental over-recording, editing or erasing of
recordings, you can protect them using “Setup” menu.
Insert a recordable disc.
1 In stop mode, press [SETUP].
2 Select “DVD Menu” using [K \ L], then press
[ENTER\OK].
3 Select “Disc Protect OFF A ON” using [K \ L],
then press [ENTER\OK].
4 Select “Yes” using [K \ L], then press
[ENTER\OK].
The disc is protected.
5 Press [SETUP] to exit.
Note
• The Disc Protect setting is available only when a disc
recorded in VR or +VR mode is inserted.
• You can select only “Disc Protect ON A OFF” when a
protected disc is inserted.
To cancel the disc protect:
• Select “Disc Protect ON A OFF” at step
3, then select “Yes”.
• If you insert a disc protected with this unit, “Disc Protect
ON A OFF” will appear instead of “OFF A ON”.
Finalising Discs
You will need to finalise discs to play them back in other units.
Finalising may take from several minutes up to an hour.
A shorter recording period on the disc will require a longer
time period for finalisation. Do not unplug the mains cable
during finalisation.
Insert a recordable disc before finalising.
1 In stop mode, press [SETUP].
2 Select “DVD Menu” using [K \ L], then press
[ENTER\OK].
3 Select “Finalise” using [K \ L], then press
[ENTER\OK].
4 Select “Yes” using [K \ L], then press
[ENTER\OK].
Finalising will start.
To move a title:
To erase all the titles in the dubbing title list:
XP SP LP EP SLP
500 MB
3000 MB
Please select REC MODE.
High Auto
Dubbing Titles
Start Dubbing?
Yes
No
Timer Recording is in standby.
Start Dubbing?
Yes
No
DVD-RW
To Next Page
Loading...
Need help?
General
