TP-Link TL-SG116P User Manual

Connection
© 2023 TP-Link 7106510236 REV4.2.1
Installation Guide
5/6/16-Port Gigabit Desktop PoE Switch
LED Explanation
Note: For simplicity, we will take TL-SG1005P for example throughout this Guide.
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. TL-SG1005LP can supply up to 30 W for each PoE port and 40 W for all PoE ports.
3. TL-SG1005P can supply up to 30 W for each PoE port and 65 W for all PoE ports.
4. TL-SG1006PP can supply up to 60 W for port 1, 30W for other single PoE port, and 64 W
for all PoE ports.
5. TL-SG116P can supply up to 30 W for each PoE port and 120 W for all PoE ports.
DC Power Adapter
AC Power Cord
IP Camera AP IP Phone
Router
LAN Port WAN Port
Internet
Ethernet Ports (1-5)
PoE Ports (1-4)
Power
On: Power on
O: Power o
Power
Link/Act and PoE Status
On: Providing PoE power
Flashing: Current-overload/Short-circuit
O: Not providing PoE power
On (Green): Connected to a 1000 Mbps
device
On (Yellow): Connected to a 10/100
Mbps device
Flashing: Transmitting/receiving data
O: No device is connected to the
corresponding port.
PoE MAX
PoE Max
TL-SG1005LP
On: 33 W ≤ Total power supply < 40 W
Flashing: Total power supply ≥ 40 W
O: Total power supply < 33 W
TL-SG1005P
On: 58 W ≤ Total power supply < 65 W
Flashing: Total power supply ≥ 65 W
O: Total power supply < 58W
TL-SG116P
On: Total power supply ≥ 113 W
Flashing: Total power supply ≥ 113 W and
lasts for more than 2 minutes
O: Total power supply < 113W
PoE Devices
Switches Explanation
Priority (for TL-SG116P)
O: All the ports transmit data with the same priority.
On: The corresponding ports transmit data with a higher priority than other ports. When congestion
occurs, packets which are transmitted by the ports with a higher priority occupy the whole bandwidth.
Isolation (for TL-SG116P)
O: Ports can transmit data with each other.
On: The corresponding ports cannot transmit data with other downlink ports. They can transmit data
only with the uplink ports (ports 15-16 of TL-SG116P).
Extend (for TL-SG1005P/TL-SG1006PP/TL-SG116P)
O: The corresponding ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m away.
On: The corresponding ports run at 10 Mbps and support PoE power supply up to 250 m away.
Recovery (for TL-SG1005P/TL-SG1006PP/TL-SG116P)
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch
nds that the PD works abnormally, the switch will reboot it.
Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend(1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.
TL-SG1006PP
On: 57 W ≤ Total power supply < 64 W
Flashing: Total power supply ≥ 64 W
O: Total power supply < 57W

TP-Link TL-SG116P Specifications

General

Switch type	Unmanaged
Quality of Service (QoS) support	Yes
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
Product color	Black
Housing material	Metal
Number of VLANs	32
Networking standards	IEEE 802.1Q, IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u
Virtual LAN features	Protocol-based VLAN, Tagged VLAN
Cable types supported	Cat3, Cat4, Cat5, Cat5e, Cat6
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 1000BASE-T
Input current	0.6 A
AC input voltage	220 V
DC input voltage	9 V
AC input frequency	50 Hz
Power consumption (max)	144.28 W
Power consumption (typical)	11.72 W
Heat dissipation	490.55 BTU/h
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
Jumbo frames	9000
Forwarding rate	23.81 Mpps
Number of queues	4
MAC address table	8000 entries
Packet buffer memory	4.1 MB
Package depth	434 mm
Package width	227 mm
Package height	70 mm
Package weight	2000 g

Weight and Dimensions

Depth	111.7 mm
Width	286 mm
Height	25.4 mm

Summary

LED Explanation and Indicators

Power LED Status

Explains the Power LED states (On/Off) for device power status.

PoE MAX LED Indicators

Details PoE Max LED status and power thresholds for different switch models.

Link/Act and PoE Status LEDs

Describes Link/Act and PoE status LEDs for network connectivity and PoE power provision.

Switching Features Explanation

Priority Setting

Explains how the Priority switch affects data transmission priority on TL-SG116P.

Extend Mode Functionality

Describes Extend switch for longer cable reach (up to 250m) at reduced speed.

Isolation Mode Functionality

Details Isolation switch preventing port-to-port communication on TL-SG116P.

PoE Auto Recovery Feature

Explains PoE Auto Recovery feature for rebooting abnormal PoE powered devices.

Technical Specifications

General Specifications

Provides details on standards, interface, network media, switching capacity, and MAC address learning.

Environmental and Physical Specifications

Details operating/storage temperature and humidity for the device.

Frequently Asked Questions (FAQ)

Power LED Troubleshooting

Addresses why the Power LED might not be lit and provides troubleshooting steps.

Link/Act LED Connectivity Issues

Explains why the Link/Act LED may not light up when a device is connected.

PoE Power Supply Limitations

Explains PoE power delivery issues due to total power consumption limits.

PoE Auto Recovery Usage Notes

Provides important considerations before using the PoE Auto Recovery feature.

Safety and Compliance Information

General Safety Precautions

Lists essential safety guidelines for using the TP-Link device.

Declarations of Conformity

Provides EU and UK declarations of conformity for the device.