Trane Odyssey TTA3004 C Series User Manual

SSAAFFEETTYY WWAARRNNIINNGG
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning
equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person
could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that
are attached to the equipment.
March 2020
SSSS--SSVVXX000011AA--EENN
Installation, Operation, and Maintenance
Split System Air Conditioners
Odyssey™™ with Symbio™™
Controls
Cooling Condenser, R-410A 5 to 25 Tons and
R-22 Dry Charge 7.5, 10, 15 and 20 Tons
((6600 HHzz))
TTA0724*A/D
TTA0904*A/D
TTA1204*C/D
TTA1504*D
TTA1804*C/D
TTA2404*C/D
TTA3004*C
TTA0902*A
TTA1202*A
TTA1802*D
TTA2402*D
((5500 HHzz))
TTA0604DA/D
TTA0764DA/D
TTA1014DC/D
TTA1264DD
TTA1564DC/D
TTA2014DC/D
TTA2514DC

Trane Odyssey TTA3004 C Series Specifications

General

Brand	Trane
Model	Odyssey TTA3004 C Series
Category	Air Conditioner
Language	English

Summary

Introduction and Safety Precautions

Safety Advisories and Warnings

Defines warning, caution, and notice advisories for safe operation and potential hazards.

Responsible Refrigerant Handling Practices

Emphasizes adherence to refrigerant handling regulations and environmental considerations.

Field Wiring and Grounding Requirements

Personal Protective Equipment (PPE)

Refrigerant Pressure and Explosion Hazards

Model Number Description

Pre-Installation Procedures

Unit Inspection and Testing

Covers inspection for shipping damage, checklist completion, and refrigerant leak testing.

Lifting Recommendations

Unit Mounting and Piping Installation

Unit Mounting Requirements

Details requirements for unit mounting, structural preparation, rooftop, and ground level.

Installation Checklist

Refrigerant Piping Installation

Refrigerant Line Insulation and Electrical Wiring

Electrical Wiring Installation

Ensures proper power wiring, thermostat installation, and connection tightness.

Dimensional Data

Unit Weights

Unit Lifting Points

Installation: Refrigerant Piping Guidelines

Allowable Elevation Differences

Installation: Refrigerant Piping Procedures (Outdoor Units)

R-410A Refrigerant Handling

Refrigerant Piping and Leak Check Procedures

Refrigerant Piping Procedures (Indoor Unit)

Leak Check Procedures

Provides warnings and instructions for performing safe leak tests using dry nitrogen.

Installation: Charging Procedures

Liquid Charging Process

Refrigerant Charging Adjustments

Installation: Charging Levels

Estimated Charge Levels

Installation: Charging and Wiring

Liquid Charging Safety

Field Electrical Wiring

Emphasizes proper field wiring and grounding requirements for safety and code compliance.

Installation: Power and Controls

Unit Power Supply Requirements

Symbio™™ Controls Wiring

Explains wiring requirements for Symbio controls, emphasizing copper conductors.

Installation: Symbio™™ Controller Wiring

Pairing A: Constant Volume Air Handler

Installation: Refrigerant Circuit Diagram

Typical Cooling Circuit

Pre-Start: Control Circuit Features

Control Features Overview

Troubleshooting Guide

Service Test Mode Operation

Maintenance Procedures

Monthly Inspections

Annual Inspections (Cooling Season)

Coil Cleaning Procedures

Microchannel (MCHE) Coil Cleaning

Charging Data and Pressure Curves

Wiring Diagram Matrix and Device Location

Warranty Terms and Conditions