Triumph Adler DC 6130 User Manual (English)

Other manuals for Triumph Adler DC 6130

Questions and Answers:

K
Kristine StewartAug 23, 2025
What to do if my Triumph Adler All in One Printer printouts are too light?
- B
  Bianca DouglasAug 23, 2025
  If your Triumph Adler All in One Printer's printouts are too light, several factors could be the cause. First, if the machine is in Manual Density mode, select the correct density level. Ensure the toner is evenly distributed by shaking the toner container from side to side. If there's a message indicating low toner, replace the toner container. Also, if the paper is damp, replace it. Disable EcoPrint mode if it's enabled. Finally, verify that the paper type setting matches the paper you're using.
J
Julie Johnson DDSSep 2, 2025
Why are my Triumph Adler All in One Printer printouts wrinkled or curled?
- J
  jaycarneySep 2, 2025
  If your Triumph Adler All in One Printer's printouts are wrinkled or curled, the paper might be damp. Replace the paper with new paper.
M
Mary LambSep 1, 2025
What to do if my Triumph Adler All in One Printer printouts are dirty?
- P
  Philip HamptonSep 1, 2025
  If your Triumph Adler All in One Printer's printouts are dirty, the platen or the document processor might be dirty. Clean the platen or the document processor.
M
Michelle WarrenAug 30, 2025
What to do if my Triumph Adler All in One Printer images are skewed?
- J
  Jacob ChristensenAug 31, 2025
  If images from your Triumph Adler All in One Printer are skewed, check the placement of the originals. When placing originals on the platen, align them with the slit glass. Also, verify that the paper is loaded correctly and check the position of the paper width guides.
E
ethan38Aug 29, 2025
What to do if my Triumph Adler All in One Printer copies have a moire pattern?
- M
  Michael WiseAug 29, 2025
  If copies from your Triumph Adler All in One Printer have a moire pattern, and the original is a printed photograph, set the image quality to [Photo].
J
Jonathan MurphyAug 28, 2025
Why won't my Triumph Adler All in One Printer feed originals?
- K
  Kenneth EdwardsAug 28, 2025
  If your Triumph Adler All in One Printer won't feed originals, make sure the originals are placed correctly in the document processor. Align the original width guides securely before placing the originals.
B
Breanna WillisAug 27, 2025
What to do if my Triumph Adler All in One Printer ejects blank sheets?
- M
  Michael MendozaAug 27, 2025
  If your Triumph Adler All in One Printer is ejecting blank sheets, check how the originals are loaded. When placing originals on the platen, ensure they are face-down and aligned with the slit glass. When using the document processor, place the originals face-up.
T
tylerpaulAug 27, 2025
What to do if my Triumph Adler All in One Printer printouts are too dark?
- A
  Alison LoweAug 27, 2025
  If your Triumph Adler All in One Printer's printouts are too dark, check the density settings. If the machine is in Auto Density mode, set the correct density level for auto density. If it's in Manual Density mode, select the correct density level.
R
Ryan ThompsonAug 25, 2025
What to do if my Triumph Adler All in One Printer cannot print?
- K
  Kristi GallegosAug 26, 2025
  If your Triumph Adler All in One Printer cannot print, first ensure the machine is plugged into an AC outlet and turned on. Check that the printer cable is securely connected. If the machine was powered on before connecting the cable, power it on again after connecting the cable. If the print job is paused, press [Resume]. Finally, if an error message is displayed, follow the corresponding procedure.
J
Jessica ChenAug 25, 2025
Why does my Triumph Adler All in One Printer paper often jam?
- M
  Michelle WoodAug 25, 2025
  If paper often jams in your Triumph Adler All in One Printer, several reasons could be the cause. Ensure the paper is loaded correctly. Check if the paper is of the supported type and in good condition; if not, remove it, turn it over, and reload it. Replace curled, folded, or wrinkled paper with new paper. Also, remove any loose scraps or jammed paper from the machine.