Need help?Do you have a question about the Triumph Daytona 955i and is the answer not in the manual?
General| Displacement | 955 cc |
|---|---|
| Bore x Stroke | 79 x 65 mm |
| Compression Ratio | 12.0:1 |
| Fuel System | Multipoint sequential electronic fuel injection |
| Transmission | 6-speed |
| Rear Brakes | Single 220 mm disc, 2-piston caliper |
| Front Tire | 120/70 ZR17 |
| Rear Tire | 190/50 ZR17 |
| Width | 720 mm (28.3 in) |
| Seat Height | 815 mm (32.1 in) |
| Engine Type | Liquid-cooled, inline 3-cylinder |
| Max Torque | 100 Nm (74 lb-ft) @ 8, 200 rpm |
| Final Drive | Chain |
| Frame | Aluminum beam |
| Front Suspension | 43 mm inverted telescopic fork, adjustable |
| Rear Suspension | Monoshock, adjustable |
| Front Brakes | Twin 320 mm discs, 4-piston calipers |
| Fuel Capacity | 21 litres (5.5 US gallons) |
Covers safety precautions for asbestos, general safety, hazardous substances, and engine oil.
Provides references for side indications and dimensional specifications.
Details procedures for repairs, replacements, and general force application.
Covers ignition safety, engine oils, hazardous substances, and coolant.
Details environmental precautions and braking system information.
Covers safety, jacking, engine coolant, cleaning, and lubrication practices.
Details locking devices, seals, press fitting, and bearings.
Provides an introduction to the maintenance schedule and its importance.
Information on service check sheets for technicians and maintenance tracking.
Illustrates cylinder head, valves, cam cover, and camshaft components.
Details service procedures for the cam chain tensioner and camshafts.
Explains valve clearance measurement and adjustment procedures.
Covers the steps for removing and reinstalling the cylinder head assembly.
Illustrates components of the clutch cover, assembly, and controls.
Details the removal, examination, and assembly of the clutch cable.
Covers the disassembly and reassembly of the clutch unit.
Details inspection procedures for clutch friction plates.
Illustrates the components of the balancer shaft assembly.
Covers alignment inspection and replacement of balancer plugs.
Details the process for removing and disassembling the balancer shaft.
Covers inspection, assembly, and installation of the balancer unit.
Illustrates crankshaft, connecting rod, piston, liner, and crankcase assemblies.
Covers procedures for removing and installing the engine assembly.
Details crankcase disassembly, assembly, and service procedures.
Covers service procedures for connecting rods and crankshaft components.
Illustrates input/output shafts, auxiliary gears, and selector mechanisms.
Describes the operation of auxiliary gears within the transmission.
Details service procedures for the alternator spindle and sprag clutch.
Covers service procedures for input and output shaft assemblies.
Illustrates sump, oil pump, oil cooler, and the oil circuit diagram.
Covers engine oil specifications, level checks, and oil filter replacement.
Details service procedures for the oil pump and its associated gears.
Covers service procedures for the engine sump and oil cooler.
Covers fuel requirements, system description, sensors, and actuators.
Illustrates fuel system components and details their service procedures.
Describes the operation of the Triumph service diagnostic tool.
Lists DTCs and provides non-electrical fault finding guidance.
Illustrates the cooling system and provides coolant information.
Covers coolant level inspection and replacement procedures.
Details maintenance for radiator hoses, cooling fan, and pressure cap.
Covers removal, inspection, and installation of the water pump and radiator.
Illustrates swinging arm, rear hub, suspension unit, and drop/drag links.
Covers service for the rear suspension unit and its linkage components.
Details drive chain inspection, adjustment, and lubrication procedures.
Covers removal and service of the swinging arm and drive chain.
Illustrates the components of the front fork assembly.
Illustrates components for low and tall handlebar configurations.
Provides an overview of front suspension and fork oil change procedures.
Details the procedures for dismantling and assembling the front fork.
Illustrates front and rear brake master cylinders and calipers.
Covers safety precautions and brake fluid service procedures.
Details service for front brake pads, caliper, discs, and master cylinder.
Details service for rear brake pads, caliper, disc, and master cylinder.
Illustrates front wheel and rear hub assemblies.
Covers tyre pressures, wear inspection, and important tyre information.
Details service procedures for wheels and wheel bearings.
Illustrates frame, seat rails, cockpit, panels, and footrests.
Covers seat, side panel, and belly panel removal and installation.
Details service for lower fairings and cockpit assembly removal/installation.
Covers frame inspection and procedures for frame renewal.
Illustrates instruments, alternator, starter, headlights, and lights.
Covers battery types, removal, refit, charging, and maintenance procedures.
Details headlight adjustment, bulb replacement, and lighting system service.
Provides lighting and starting/charging circuit diagrams and wiring keys.
To Next Page
