EasyManua.ls Logo

Troy-Bilt 30248 - Maintenance; General Maintenance Recommendations; Engine Maintenance; Generator Maintenance and Cleaning

Troy-Bilt 30248
32 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
SPECIFmCATmONS
Starting VVattage ....................... 5,250 watts
Wattage ............................. 3,550watts
AC Load Current at H20VoHts ............. 29.6Amps
Phase .................................. H-phase
Rated Frequency ......................... 60 Hertz
FueHTank Capacity ............... 4 U.S. gaHHons(H5 H)
Shipping VVoght .................... H30 Hbs.(59 kg)
GENERAL MAmNTENANCE
RECOMMENDATmONS
The Owner/Operator is responsibHe for making sure that
aHHperiodic maintenance tasks are completed on a timeHy
basis; that aHHdiscrepancies are corrected; and that the unit
is kept dean and 9roperH 7 stored. NEVER operate a
damaged or defective generator.
NOTE: ShouHd you have questions about repHacing
components on your Troy-BiHt generator, 9Hease caHH
l=888=61 l =6708 for assistance.
ine Maintenance
See engineoperator'smanuaH forinstructions.
I cAuTlo. 1
. Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
. Thoroughl>. wash exposed areas with soap and wate_t
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OILTO COLLECTION CENTERS.
Generator Maintenance
Generator maintenance consists of keeping the unit dean
and dry. Operate and store the unit in a dean dry
environment where it wiHHnot be exposed to excessive
dust, dirt, moisture or any corrosive vapors. CooHing air
shots in the generator must not become cHoKed with snow,
Heaves or any other foreign materiaH.
NOTE: DO NOT use a garden hose to dean generator.
'Water can enter engine fuel system and cause probHems. In
addition, if water enters generator through cooHing air sHots,
some of the water wiHHbe retained in voids and cracks of
the rotor and stator winding insuHation.V_%ter and dirt
buiHdup on the generator internal windings wiHHeventuaHHy
decrease the insuHation resistance of these windings.
WARNING
WHEN ADJUSTmNG OF[ MAKmNG REPAIRSTOYOUR
GENERATOR
• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
Use approved spark plug testett
DO NOT check for spark with spark plug removed.
Generator Clean[n
" Use a damp cloth to wipe exterior surfaces dean.
®
®
®
DO NOT expose generator to excessive moisture, dust, dirt,
Or corrosive vapors_
DO NOT insert any objects through cooling stots_
Use a soft bristle brush to Hoosen caked on dirt or oiH.
Use a vacuum cHeaner to pick up bose dirt and debris.
Use How pressure air (not to exceed 25 psi) to blow away
dirt. Inspect cooHing air shots and opening on generator.
These openings must be kept dean and unobstructed.
D ata Tag
Data tag information is very important if you need heHp from
our Customer Service Department or an authorized service
dealer.
The data tag (Figure 9) is located on the engine support on
the muffler side of the generator, For future reference, pHease
copy the modeH_ revision_ and seriaH number of the generator
in the space below.
MODEL
REV NO _
SERIAL
Copy HodeH
/ Number Here
Copy Revision
Here
Copy SeriaH
Number Here