EasyManua.ls Logo

Troy-Bilt 550 Series - User Manual

Troy-Bilt 550 Series
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
OperatOr’s Manual
Safe Operation Practices • Set-Up • Controls & Operation • Service • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all
models and the model depicted may differ from yours.
Form No. 769-11911
(September 28, 2016)
Lawn Edger — 550 Series

Table of Contents

Questions and Answers

  • F
    fevansAug 1, 2025
    How to fix Troy-Bilt 550 engine that fails to start?
    • D
      daleclarkAug 2, 2025
      If your Troy-Bilt Lawn Mower engine won't start, possible causes include an empty fuel tank, stale fuel, a disconnected spark plug wire, or a fouled spark plug. Try filling the tank with fresh gasoline, connecting the spark plug wire, or cleaning, adjusting, or replacing the spark plug. Also, the engine may need to be primed by pushing the primer bulb two or three times if equipped. For dirty air cleaner or flooded engine, refer to the Engine Operator’s Manual.
  • B
    bradleyburkeAug 6, 2025
    Why does my Troy-Bilt 550 engine run erratic?
    • J
      Joseph ShortAug 6, 2025
      If your Troy-Bilt Lawn Mower engine runs erratically, it might be due to a loose spark plug wire, stale fuel, a plugged vent in the gas cap, or water/dirt in the fuel system. Ensure the spark plug wire is connected and tightened. Drain the gasoline tank and refill with fresh fuel. Clear the vent in the gas cap of any debris. For a dirty air cleaner, refer to the Engine Operator’s Manual.
  • D
    Darlene HooverAug 11, 2025
    What to do if Troy-Bilt 550 Lawn Mower drive-belt slips?
    • N
      Nicole ColemanAug 11, 2025
      If the drive-belt slips on your Troy-Bilt Lawn Mower, it is likely worn or stretched and needs to be replaced.
  • G
    George AndersonAug 16, 2025
    What to do if my Troy-Bilt Lawn Mower engine overheats?
    • M
      Mark ChavezAug 16, 2025
      If your Troy-Bilt Lawn Mower engine overheats, check the engine oil level and add oil if it is low. Also, ensure that there is no restriction of airflow around the engine by cleaning the area around and on top of the engine. For a dirty air cleaner, refer to the Engine Operator’s Manual.
  • S
    Sarah SmithAug 21, 2025
    Why Troy-Bilt 550 idles poorly?
    • A
      ashley85Aug 21, 2025
      If your Troy-Bilt Lawn Mower idles poorly, the spark plug may be fouled, faulty, or have a gap that is too wide. Reset the gap or replace the spark plug. For a dirty air cleaner, refer to the Engine Operator’s Manual.
  • M
    Mr. Jordan ThomasAug 27, 2025
    Why Troy-Bilt 550 Lawn Mower has occasional skips at high speed?
    • J
      John GravesAug 27, 2025
      If your Troy-Bilt Lawn Mower experiences occasional skips (hesitates) at high speed, the spark plug gap might be too close. Adjust the gap, referring to the Engine Operator’s Manual for gap specifications.

Summary

Safe Operation Practices

Training

General training and familiarization with the machine before operation.

Safe Handling Of Gasoline

Precautions for handling flammable gasoline to prevent injury.

Preparation

Steps to take before operating the machine.

Operation

General guidelines for operating the machine safely.

Children

Safety measures to protect children around the equipment.

Assembly & Set-Up

Contents of Carton

List of items included in the product packaging.

Assembly

Step-by-step instructions for assembling the lawn edger.

Adjustments

How to adjust machine settings like blade bevel for optimal use.

Set-Up: Gas and Oil Fill-Up

Procedures for adding fuel and oil before initial operation.

Controls and Operation

Controls

Overview and identification of all machine controls.

Starting the Engine

Detailed steps for starting the lawn edger's engine.

Stopping The Engine

Method to safely shut down the machine's engine.

Edging

Instructions on how to perform edging tasks with the machine.

Edging Along a Curb

Technique for edging along curbs using wheel adjustment.

Beveling

How to adjust the blade for beveled cuts.

Trenching (If Equipped)

Instructions for using the optional trenching feature.

Service

Maintenance

General maintenance procedures for the lawn edger.

Engine

Engine-specific service and maintenance information.

Edger Blade

Procedures for inspecting and replacing the edger blade.

Lubrication

Points and schedule for lubricating moving parts.

Belt Replacement

Steps to replace the drive belt on the machine.

Off-Season Storage

Troubleshooting

Engine fails to start

Solutions for when the engine will not start.

Engine runs erratic

Causes and remedies for inconsistent engine operation.

Engine overheats

Reasons and fixes for the engine getting too hot.

Occasional skips (hesitates) at high speed

Troubleshooting tips for performance issues at higher speeds.

Idles poorly

How to address problems with the engine idling.

Excessive vibration

Identifying and fixing causes of excessive machine vibration.

Drive-belt slips

Solutions for a drive belt that is slipping.

Replacement Parts

Manufacturers Limited Warranty

Troy-Bilt 550 Series Specifications

General IconGeneral
Engine Displacement140cc
Deck MaterialSteel
Mulch CapableYes
Side DischargeYes
Rear BagYes
Cutting Width21 inches
Cutting Height1.25 - 3.75 in
Wheel Size7 inches front, 10 inches rear

Related product manuals