Troy-Bilt 500 Series - User Manual

Questions and Answers

C
ckiddAug 14, 2025
Why Troy-Bilt Snow Blower engine fails to start?
- K
  Katie NealAug 14, 2025
  Your Troy-Bilt Snow Blower might fail to start due to several reasons: 1. The choke might not be in the CHOKE position. Move the choke to the CHOKE position. 2. The spark plug wire might be disconnected. Connect the wire to the spark plug. 3. The fuel tank might be empty or contain stale fuel. Fill the tank with clean, fresh gasoline. 4. The engine might not be primed. Prime the engine as instructed in the Operation section. 5. The spark plug might be faulty. Clean, adjust the gap, or replace it. 6. The key might not be fully inserted into the ignition switch. Insert the key fully into the switch.
D
dennishillAug 17, 2025
How to fix Troy-Bilt Snow Blower engine that won't start using electric start?
- N
  Nancy WilliamsAug 17, 2025
  If your Troy-Bilt Snow Blower engine fails to start using the electric start button, make sure the extension cord is connected properly. Connect one end of the extension cord to the electric starter outlet and the other end to a three-prong 120-volt, grounded, AC outlet.
R
Robert HoweAug 21, 2025
What to do if my Troy-Bilt Snow Blower loses power?
- S
  sshafferAug 21, 2025
  If your Troy-Bilt Snow Blower is losing power: 1. Check if the spark plug wire is loose. Connect and tighten the spark plug wire. 2. See if the gas cap vent hole is plugged. Remove any ice and snow from the gas cap, ensuring the vent hole is clear.
A
anthony80Aug 25, 2025
What to do if my Troy-Bilt Snow Blower unit fails to discharge snow?
- J
  Joseph AcostaAug 25, 2025
  If your Troy-Bilt Snow Blower fails to discharge snow, consider these solutions: 1. The chute assembly might be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool or a stick. 2. A foreign object might be lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger with a clean-out tool or a stick. 3. The auger control cable might need adjustment. Refer to Auger Control Test. 4. The auger belt might be loose or damaged. Refer to Maintenance & Adjustments section. 5. Shear pins might be sheared. Replace them with new shear pins.
L
Luke OlsonAug 27, 2025
Why Troy-Bilt Snow Blower engine running erratically?
- T
  Tiffany ZhangAug 27, 2025
  If your Troy-Bilt Snow Blower engine is running erratically, it could be due to: 1. The engine running on CHOKE. Move the choke lever to the RUN position. 2. Stale fuel. Fill the tank with clean, fresh gasoline. 3. Water or dirt in the fuel system. Drain the fuel tank and refill with fresh fuel. 4. Carburetor out of adjustment. Contact an authorized Service Center. 5. Engine over-governed. Contact an authorized Service Center.
C
Crystal RamosAug 30, 2025
What to do if my Troy-Bilt Snow Blower vibrates excessively?
- C
  Christina Campbell MDAug 31, 2025
  If your Troy-Bilt Snow Blower is vibrating excessively: 1. Check for loose parts or a damaged auger. Stop the engine immediately, disconnect the spark plug wire, and tighten all bolts and nuts. If the vibration continues, have the unit serviced by an authorized Service Center.
C
Christopher AllenSep 3, 2025
How to fix Troy-Bilt Snow Blower that fails to propel itself?
- J
  Jamie ChaseSep 3, 2025
  If your Troy-Bilt Snow Blower fails to propel itself: 1. The drive control cable may need adjustment. Adjust the drive control cable. Refer to Maintenance & Adjustments section. 2. The drive belt may be loose or damaged. Replace the drive belt. Refer to Service section. 3. The friction wheel may be worn. Replace the friction wheel. Refer to Service section.
R
ricecharlesSep 6, 2025
Why Troy-Bilt Snow Blower engine overheats?
- T
  Timothy MaysSep 6, 2025
  If your Troy-Bilt Snow Blower engine overheats, it may be because the carburetor is not adjusted properly. Contact an authorized Service Center.
A
Adam SotoSep 10, 2025
Why Troy-Bilt Snow Blower chute fails to easily rotate?
- C
  Christopher CamposSep 10, 2025
  If the chute on your Troy-Bilt Snow Blower fails to easily rotate 180 degrees, it may be because the chute was assembled incorrectly. Unassemble the chute control and reassemble as directed in the Assembly & Set-up section.