Tuthill 150 - Assembly Clearances

Manual 2003 Rev D p/n 2003
31
MODEL
GEAR END FREE END INTERLOBE TIP-DOWEL
TIP-PORT
150
0.003 – 0.005 in.
(0.08 – 0.13 mm)
0.006 – 0.010 in.
(0.15 – 0.25 mm)
CENTER
TIMED
0.003 – 0.007 in.
(0.08 – 0.18 mm)
0.006 – 0.010 in.
(0.15 – 0.25 mm)
240
0.003 – 0.005 in.
(0.08 – 0.13 mm)
0.012 – 0.017 in.
(0.30 – 0.43 mm)
0.003 – 0.007 in.
(0.08 – 0.18 mm)
0.006 – 0.010 in.
(0.15 – 0.25 mm)
400
0.003 – 0.005 in.
(0.08 – 0.13 mm)
0.012 – 0.017 in.
(0.30 – 0.43 mm)
0.003 – 0.007 in.
(0.08 – 0.18 mm)
0.006 – 0.010 in.
(0.15 – 0.25 mm)
540
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
CENTER
TIMED
0.017 – 0.022 in.
(0.43 – 0.56 mm)
0.017 – 0.022 in.
(0.43 – 0.56 mm)
720
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
0.017 – 0.022 in.
(0.43 – 0.56 mm)
0.017 – 0.022 in.
(0.43 – 0.56 mm)
850
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
CENTER
TIMED
0.007 – 0.012 in.
(0.18 – 0.30 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
1200
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.014 – 0.019 in.
(0.36 – 0.48 mm)
0.007 – 0.012 in.
(0.18 – 0.30 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
1600
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.017 – 0.022 in.
(0.43 – 0.56 mm)
0.007 – 0.012 in.
(0.18 – 0.30 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
2000
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.021 – 0.026 in.
(0.53 – 0.66 mm)
0.007 – 0.012 in.
(0.18 – 0.30 mm)
0.011 – 0.016 in.
(0.28 – 0.41 mm)
2700
0.004 – 0.007 in.
(0.10 – 0.18 mm)
0.025 – 0.030 in.
(0.64 – 0.76 mm)
0.008 – 0.013 in.
(0.20 – 0.33 mm)
0.012 – 0.017 in.
(0.30 – 0.43 mm)
ASSEMBLY CLEARANCES
09