What to do if Tuthill Water Pump has fluid leakage?
If your Tuthill Water Pump is leaking fluid, there are several potential causes. First, check all o-ring gaskets. A dirty shaft seal can also cause leakage, so clean the seal and seal cavity. If the shaft seal is bad, replace it. Ensure the fluid is compatible by referring to the wetted parts list and fluid manufacturer. Finally, check and tighten all fasteners.
Why Tuthill Water Pump won't prime?
If your Tuthill Water Pump isn't priming, start by checking the suction line for leaks. Inspect the bypass valve to ensure it moves freely and is free of debris. Check the vanes and slots for any nicks, burrs, or wear. Inspect the rotor and vanes for excessive wear or damage, and replace if necessary. Ensure the pump outlet, hose, nozzle, and filter are not blocked. Vapor lock can also prevent priming; reduce the vertical and horizontal distance from the pump to the liquid and remove the automatic nozzle.
What to do if Tuthill Water Pump motor overheats?
If your Tuthill Water Pump motor is overheating, consider the following: If you are pumping high viscosity fluids, know that these fluids can only be pumped for short periods of time (less than 30 minutes duty cycle). Also, remove and clean the screen. Remove and clean the suction pipe. Clean and check pump rotor and vanes.
Why Tuthill Water Pump has low capacity?
If your Tuthill Water Pump has low capacity, begin by removing and cleaning the screen. Check the suction line for leaks or restrictions, ensuring it's not too small, too long, or not airtight. Remove and inspect the bypass valve, ensuring it moves freely and is free of debris. Check the vanes and slots for wear. Inspect the rotor and vanes for excessive wear or damage, replacing them if necessary. Replace any damaged hose or nozzle. Replace the filter if it is plugged. Ensure the fluid level is adequate by filling the tank.
What to do if Tuthill Water Pump motor stalls?
If your Tuthill Water Pump motor stalls, remove and inspect the bypass valve, ensuring it moves freely and is free of debris. Check the incoming line voltage while the pump is running. Check rotor & vanes for excessive wear or damage. Clean debris from pump cavity.
How to troubleshoot Tuthill Water Pump that runs slowly?
If your Tuthill Water Pump runs slowly, check the incoming line voltage while the pump is running. Inspect the vanes and slots for nicks, burrs, and wear. Check for loose connections in the wiring.
What to do if Tuthill Water Pump hums but will not operate?
If your Tuthill Water Pump hums but won't operate, clean out the pump cavity. Check incoming line voltage while pump is on. Remove all debris & replace insert.
What to do if Tuthill Water Pump motor inoperative?
If your Tuthill Water Pump motor is inoperative, check the incoming power and check the wiring.
Procedures and materials for mounting the pump onto a skid tank.
Procedures and materials for mounting the pump on a concrete island with a pedestal kit.
Guidance on installing an anti-siphon tube to prevent liquid siphoning.
Steps for assembling and installing the suction pipe into the bung adapter.
Step-by-step guide for connecting the pump's electrical wiring to the power supply.
Instructions for correctly installing the nozzle boot in a horizontal position.
Lists compatible fluids and advises checking suppliers for fluid compatibility.
Information on safety testing compliance with UL Laboratories standards.
Instructions on using a padlock for securing the pump nozzle.
Procedures and materials for mounting the pump onto a skid tank.
Procedures and materials for mounting the pump on a concrete island with a pedestal kit.
Guidance on installing an anti-siphon tube to prevent liquid siphoning.
Steps for assembling and installing the suction pipe into the bung adapter.
Step-by-step guide for connecting the pump's electrical wiring to the power supply.
Instructions for correctly installing the nozzle boot in a horizontal position.
Lists compatible fluids and advises checking suppliers for fluid compatibility.
Information on safety testing compliance with UL Laboratories standards.
Instructions on using a padlock for securing the pump nozzle.
General| Brand | Tuthill |
|---|---|
| Model | FR700V Series |
| Category | Water Pump |
| Language | English |
To Next Page