Tuthill FILL-RITE 700V Series

Questions and Answers

S
Stephen WilliamsAug 12, 2025
Why Tuthill Water Pump won't prime?
- B
  bakermelissaAug 12, 2025
  If your Tuthill Water Pump won't prime, it could be due to several reasons: * A suction line problem: Check for leaks in the suction line. * An open bypass valve: Remove and inspect the valve to ensure it moves freely and is free of debris. * Sticking vanes: Check the vanes and slots for nicks, burrs, and wear. * Excessive rotor or vane wear: Inspect the rotor and vanes for excessive wear or damage; replace if necessary. * A blocked outlet: Check the pump outlet, hose, nozzle, and filter for blockage. * Vapor lock: Reduce the vertical and horizontal distance from the pump to the liquid; remove the automatic nozzle.
T
teresaspencerAug 16, 2025
What to do if Tuthill Water Pump has low capacity?
- C
  Christian PerezAug 16, 2025
  If your Tuthill Water Pump has low capacity, consider the following: * Excessive dirt in the screen: Remove and clean the screen. * Suction line issues: Check the suction line for leaks or restrictions; ensure it's not too small, too long, or not airtight. * Bypass valve sticking: Remove and inspect the valve to ensure it moves freely and is free of debris. * Vanes sticking: Check the vanes and slots for wear. * Excessive rotor or vane wear: Inspect the rotor and vanes for excessive wear or damage; replace if necessary. * Hose or nozzle damage: Replace the hose or nozzle. * Plugged filter: Replace the filter. * Low fluid level: Fill the tank.
B
Beth RoblesAug 20, 2025
What causes Tuthill Water Pump motor to overheat?
- S
  Sheryl ToddAug 20, 2025
  The motor of your Tuthill Water Pump may overheat due to several causes: * Pumping high viscosity fluids: These fluids can only be pumped for short periods (less than 30 minutes duty cycle). * Clogged screen: Remove and clean the screen. * Restricted suction pipe: Remove and clean the pipe. * Pump rotor lock-up: Clean and check the pump rotor and vanes.
T
Tara BaileyAug 25, 2025
Why does Tuthill Water Pump run slowly?
- K
  Kelly DavisAug 25, 2025
  Your Tuthill Water Pump might be running slowly due to these reasons: * Incorrect voltage: Check the incoming line voltage while the pump is running. * Vanes sticking: Inspect the vanes and slots for nicks, burrs, and wear. * Wiring problem: Check for loose connections.
K
karenwyattAug 27, 2025
What to do if Tuthill Water Pump motor stalls?
- W
  wilsonmaryAug 28, 2025
  If the motor of your Tuthill Water Pump stalls, check the following: * Bypass valve sticking: Remove and inspect the valve; it must move freely and be free of debris. * Low voltage: Check the incoming line voltage while the pump is running. * Excessive rotor or vane wear: Check the rotor and vanes for excessive wear or damage. * Debris in the pump cavity: Clean debris from the pump cavity.
G
gabriel46Aug 31, 2025
Why Tuthill Water Pump has fluid leakage?
- R
  rogersmichaelAug 31, 2025
  Fluid leakage in your Tuthill Water Pump can be caused by: * A bad o-ring gasket: Check all o-ring gaskets. * A dirty shaft seal: Clean the seal & seal cavity. * A bad shaft seal: Replace the seal. * An incompatible fluid: Refer to the wetted parts list to the fluid manufacturer. * Loose fasteners: Tighten the fasteners.
P
Pamela JohnsonSep 3, 2025
What causes Tuthill Water Pump motor inoperative?
- G
  Glenda JonesSep 4, 2025
  If the motor of your Tuthill Water Pump is inoperative, consider these potential causes: * No power: Check incoming power. * Incorrect/loose wiring: Check wiring.
E
Elijah TurnerSep 7, 2025
What to do if Tuthill Water Pump hums but will not operate?
- A
  Ariel KnightSep 7, 2025
  If your Tuthill Water Pump hums but won't operate, it could be due to: * Dirt in the pump cavity: Clean out the pump cavity. * A broken key: Remove all debris & replace the key.