Tyco MX4428 - Chapter 3 Device Information and Programming (cont.); 3.16 MIM800 and MIM801 Mini Input Modules; 3.17 CIM800 Contact Input Module; 3.18 CP820 Manual Call Point

MX4428 MXP Engineering /Technical Manual Document: LT0273
Page vi 24 March 2006 Issue 1.5
8.1.9 MXP EVENT LOG ..........................................................................................................8-9
8.2 FLASH PROGRAMMING....................................................................................................8-10
8.2.1 FILES REQUIRED........................................................................................................ 8-10
8.2.2 PROCEDURE............................................................................................................... 8-10
CHAPTER 9 DEVICE PROCESSING.....................................................................9-1
9.1 EXPONENTIAL FILTER........................................................................................................ 9-2
9.2 STEP LIMITING FILTER........................................................................................................9-2
9.3 HEAT PROCESSING.............................................................................................................9-4
9.3.1 CONVERSION OF DETECTOR READING TO °C........................................................ 9-4
9.4 PHOTO PROCESSING..........................................................................................................9-6
9.4.1 SMARTSENSE PROCESSING......................................................................................9-6
9.4.2 SMARTSENSE ENHANCEMENT.................................................................................. 9-6
9.4.3 FASTLOGIC PROCESSING..........................................................................................9-7
9.5 CO PROCESSING................................................................................................................. 9-8
9.5.1 CALIBRATION AND TEMPERATURE COMPENSATION ............................................ 9-8
9.5.2 “ENHANCEMENT” .........................................................................................................9-8
9.5.3 CO PROCESSING .........................................................................................................9-8
9.6 IONISATION PROCESSING ................................................................................................. 9-9
9.7 MIM800 / CIM800 / MIM801 PROCESSING........................................................................9-10
9.7.1 ALGORITHM - MIM800, CIM800 ................................................................................. 9-11
9.7.2 ALGORITHM - MIM801................................................................................................9-11
9.8 DIM PROCESSING..............................................................................................................9-12
9.8.1 LOAD GRAPH..............................................................................................................9-12
9.8.2 DIM MODEL .................................................................................................................9-12
9.8.3 ALGORITHM - DIM800 ................................................................................................9-12
9.8.4 SUPPLY MONITORING - DIM800............................................................................... 9-13
9.9 RIM PROCESSING..............................................................................................................9-13
9.9.1 POSITION MONITORING............................................................................................9-13
9.10 SNM PROCESSING ............................................................................................................9-13
9.10.1 PROGRAMMING..........................................................................................................9-13
9.10.2 SUPPLY FAULT DETERMINATION............................................................................9-13
9.10.3 EOL AND POSITION MONITORING........................................................................... 9-13
9.11 LPS PROCESSING .............................................................................................................9-14
9.11.1 ELD AND POSITION MONITORING ...........................................................................9-14
9.12 VLC800 PROCESSING.......................................................................................................9-14
9.12.1 GENERAL.....................................................................................................................9-14
9.13 FILTER STEP LIMITS..........................................................................................................9-15
9.14 ZONE ALARM TEST ...........................................................................................................9-15
9.15 ZONE FAULT TEST ............................................................................................................9-15
9.16 AUTOTEST AND SYSTEM TEST.......................................................................................9-15
9.17 NON LATCHING TEST MODE............................................................................................9-16
9.18 COMMISSION MODE..........................................................................................................9-16
9.19 FAST POINT TEST..............................................................................................................9-16
9.20 SLOW POINT TEST ............................................................................................................9-16
9.21 SUMMARY OF ALL TEST MODES .................................................................................... 9-16
9.22 ANCILLARY FILTERING.....................................................................................................9-17
9.23 RESET .................................................................................................................................9-18
9.23.1 RESET OF ADDRESSABLE DETECTOR................................................................... 9-18
9.23.2 RESET OF DIM MODULE............................................................................................ 9-18
9.23.3 RESET OF ANCILLARY INPUT DEVICE .................................................................... 9-18
9.23.4 RESET OF ANCILLARY OUTPUT DEVICE ................................................................9-18
9.24 DEVICE INITIALISATION AND POLLING..........................................................................9-19
9.25 SOFTWARE VERSIONS.....................................................................................................9-20
CHAPTER 10 MXP LOOP FILTER BOARD ........................................................
10-1
10.1 USE OF MXP LOOP FILTER BOARD................................................................................ 10-2
10.2 FITTING ...............................................................................................................................10-2
10.3 DIAGNOSTICS ....................................................................................................................10-3