Ubiquiti NanoStation M2 Manual

2021-06-18 08:10 1/2 Anleitung – Unbrick Nanostation
Netz39 - https://www.netz39.de/wiki/
Anleitung – Unbrick Nanostation
Manual for Unbrick a UBNT Nanostation
compatible for:
Nanostation M2
Nanostation M2 XW
Nanostation loco M2
Nanostation loco M2 XW
Nanostation M5
Nanostation M5 XW
Nanostation loco M5
Nanostation loco M5 XW
(1) Download the AirOS 5.5.x firmware executable from the Ubiquiti website. Choose XM or XW
version depending on your device, If you don’t know, take a guess!
XM.v5.5.11.28002.150723.1344.bin, changelog
for: AG-HP-2G16, AG-HP-5G23, AG-HP-5G27, AirGrid M2, AirGrid M5, AR, AR-HP, BM2HP,
BM2-Ti, BM5HP, BM5-Ti, LiteStation M5, locoM2, locoM5, locoM9, M2, M3, M365, M5,
M900, NB-2G18, NB-5G25, NBM3, NBM365, NBM9, NS2, NSM3, NSM365, NSM5, PBM10,
PBM3, PBM5, Power AP N
XW.v5.5.10-u2.28005.150723.1358.bin, changelog
for: AG-HP-2G16, AG-HP-2G20, AG-HP-5G23, AG-HP-5G27, AirGrid M, AirGrid M2, AirGrid
M5, locoM2, locoM5, locoM9, M2, M3, M365, M5, M900, NBE-M2-13, NBE-M5-16, NBE-
M5-19, NSM2, NSM3, NSM365, NSM5, PBM3, PBM365, PBM5, RM2-Ti, RM5-Ti
(2) Start device into config/maintenance mode: in this precise order, unpower device,
configure PC into static IP 192.168.1.3 Netmask 255.255.255.0
press and maintain reset button
plug device in, release reset button as soon as LEDs blink (please wait 20-30 seconds)
(note 1: LED blink pattern is different depending on device: Sometimes a single LED blinking 3/4
on, 1/4 off, sometimes two LEDs blinking "sideways")
(note 2: the static-IP connection to the device must be established before it boots into config
mode. It was tricky rebooting the device fast enough that the PC connection did not go down.
YMMV.)
(3) TFTP the AirOS 5.5.x firmware into the device:
tftp 192.168.1.20
(note: use this IP regardless of what firmware is already on the device)

Ubiquiti NanoStation M2 Specifications

General

Frequency	2.4 GHz
Throughput	150+ Mbps
Networking Interface	10/100 Ethernet Port
Operating Temperature	-30 to 75° C
Dimensions	186 x 48 x 130 mm (7.32 x 1.89 x 5.12 in)
Weight	380 g (13.4 oz)
RoHS Compliance	Yes
Operating Frequency	2.4 GHz
Enclosure Characteristics	Outdoor UV Stabilized Plastic
Operating Humidity	5 to 95% Non-Condensing
Shock and Vibration	ETSI300-019-1.4
Product Name	NanoStation M2
Category	Wireless Access Point
Wireless Standards	802.11b/g/n
Frequency Range	2.4 GHz
MIMO	2x2
Ethernet Ports	1
Processor	400 MHz
Power Supply	24V, 0.5A PoE
Processor Specs	400 MHz
Wireless Approvals	FCC, IC, CE
Power Method	Passive PoE (Pairs 4, 5+; 7, 8 Return)
Antenna Type	Integrated
PoE	24V Passive PoE
Mounting	Pole Mounting Kit included
Memory	32 MB SDRAM, 8 MB Flash