Vacon CX - Page 31

Vacon Plc Phone: +358-(0)201 2121 Fax: +358-(0)201 212 205
Service: +358-40-8371 150 E-mail: vacon@vacon.com
Page 30
VV
VV
V
aconacon
aconacon
acon
Multi-purpose Control Application IIMulti-purpose Control Application II
Multi-purpose Control Application IIMulti-purpose Control Application II
Multi-purpose Control Application II
3. 63. 6
3. 63. 6
3. 6
Digital output functionDigital output function
Digital output functionDigital output function
Digital output function
3. 73. 7
3. 73. 7
3. 7
Relay output 1 functionRelay output 1 function
Relay output 1 functionRelay output 1 function
Relay output 1 function
3. 83. 8
3. 83. 8
3. 8
Relay output 2 functionRelay output 2 function
Relay output 2 functionRelay output 2 function
Relay output 2 function
Setting value Signal content
0 = Not used Out of operation
Digital output DO1 sinks the current and programmable
relay (RO1, RO2) is activated when:
1 = Ready The frequency converter is ready to operate
2 = Run The frequency converter operates (motor is running)
3 = Fault A fault trip has occurred
4 = Fault inverted A fault trip has not occurred
5 = Vacon overheat warning The heat-sink temperature exceeds +70°C
6 = External fault or warning Fault or warning depending on parameter 7
..
..
. 2
7 = Reference fault or warning Fault or warning depending on parameter 7
..
..
. 1
- if analogue reference is 4—20 mA and signal is <4mA
8 = Warning Always if a warning exists
9 = Reversed The reverse command has been selected
10= Jogging speed Jogging speed has been selected with digital input
11 = At speed The output frequency has reached the set reference
12= Motor regulator activated Overvoltage or overcurrent regulator was activated
13= Output frequency supervision 1 The output frequency goes outside of the set supervision
Low limit/ High limit (par. 3
..
..
. 9 and 3
..
..
. 10)
14= Output frequency supervision 2 The output frequency goes outside of the set supervision
Low limit/ High limit (par. 3
..
..
. 11 and 3
..
..
. 12)
15= Torque limit supervision The motor torque goes outside of the set supervision
Low limit/ High limit (par. 3
..
..
. 13 and 3
..
..
. 14)
16= Reference limit supervision Reference goes outside of the set supervision
Low limit/ High limit (par. 3
..
..
. 15 and 3
..
..
. 16)
17= External brake control External brake ON/OFF control with programmable de-
lay (par 3
..
..
. 17 and 3
..
..
. 18)
18= Control from I/O terminals External control mode selected with progr. push-button
#2
19= Frequency converter Temperature on frequency converter goes outside the
temperature limit supervision set supervision limits (par. 3
..
..
. 19 and 3
..
..
. 20)
20= Unrequested rotation direction Rotation direction of the motor shaft is different from the
requested one
21 = External brake control inverted External brake ON/OFF control (par. 3.17 and 3.18),
output active when brake control is OFF
22 = Termistor fault or warning The termistor input of option board indicates
overtemperature. Fault or warning depending on
parameter 7.19
Table 6-2 Output signals via DO1 and output relays RO1 and RO2.
3. 93. 9
3. 93. 9
3. 9
Output frequency limit 1, supervision functionOutput frequency limit 1, supervision function
Output frequency limit 1, supervision functionOutput frequency limit 1, supervision function
Output frequency limit 1, supervision function
3. 13. 1
3. 13. 1
3. 1
11
11
1
Output frequency limit 2, supervision functionOutput frequency limit 2, supervision function
Output frequency limit 2, supervision functionOutput frequency limit 2, supervision function
Output frequency limit 2, supervision function
0 = No supervision
1 = Low limit supervision
2 = High limit supervision
If the output frequency goes under/over the set limit (3
..
..
. 10, 3
..
..
. 12) this function
generates a warning message via the digital output DO1 and via a relay output RO1
or RO2 depending on the settings of the parameters 3
..
..
. 6—3
..
..
. 8.
3. 103. 10
3. 103. 10
3. 10
Output frequency limit 1, supervision valueOutput frequency limit 1, supervision value
Output frequency limit 1, supervision valueOutput frequency limit 1, supervision value
Output frequency limit 1, supervision value
3. 123. 12
3. 123. 12
3. 12
Output frequency limit 2, supervision valueOutput frequency limit 2, supervision value
Output frequency limit 2, supervision valueOutput frequency limit 2, supervision value
Output frequency limit 2, supervision value
The frequency value to be supervised by the parameter 3
..
..
. 9 (3
..
..
. 11).
See figure 6-16.