What to do if the water pressure sensor or cable harness hydraulics are defective in my Vaillant ecoTEC plus 615?
If the water pressure sensor or cable harness hydraulics are defective in your Vaillant Boiler, it could be due to a broken line to the water pressure sensor, a short-circuit at 0 V, or a defective water pressure sensor. Inspect and replace the water pressure sensor or repair the line.
What does it mean if my Vaillant ecoTEC plus 615 shows eBUS undervoltage?
An eBUS undervoltage indication means there could be a short circuit on the eBUS, an overload on the eBUS, or two power sources on the eBUS with different polarity. Check the eBUS connections and power sources.
What to do if there is a short circuit in the flow-NTC of my Vaillant ecoTEC plus 615?
If there is a short circuit in the flow-NTC of your Vaillant Boiler, it could be due to the NTC plug shorted to the casing or a defective NTC. Inspect and replace the NTC if defective.
Why is overheating protection triggered on primary heat exchanger in my Vaillant ecoTEC plus 615 Boiler?
Overheating protection on the primary heat exchanger may be triggered because the cable or cable connection of the fuse in the primary heat exchanger is defective, or the primary heat exchanger itself is defective. Inspect and replace the cable or primary heat exchanger.
Why is the safety temperature limiter by NTC activated in my Vaillant Boiler?
The safety temperature limiter by NTC might be activated because the Flow-NTC is not correctly thermal-connected or is defective, causing the appliance not to shut down. Check the thermal connection of the Flow-NTC and replace it if defective.
How to fix Return NTC short circuit in Vaillant Boiler?
A Return NTC short circuit can be caused by a defective NTC, a short circuit in the cable harness, or a cable/casing shortcut. Replace the NTC and inspect the cable harness.
What to do if my Vaillant Boiler shows flow and/or return NTC fault?
If there is a flow and/or return NTC fault, the flow and/or return NTC is defective (tolerances too big). Replace the flow and/or return NTC.
What to do if the gas supply to my Vaillant Boiler is off?
If the gas supply to your Vaillant Boiler is off or not correctly purged, check that the gas supply to the boiler is on, that it has been correctly purged, and that an inlet pressure of 20 mbar is available at the gas valve.
Why does the flame go off during operation in my Vaillant ecoTEC plus 615 Boiler?
If the flame goes off during operation and subsequent ignition attempts fail in your Vaillant Boiler, it could be due to a temporarily stopped gas supply, spark failure in the ignition transformer, or faulty earthing of the appliance. Check gas supply and ignition system for faults.
What to do if my Vaillant ecoTEC plus 615 is dry firing?
If your Vaillant Boiler is dry firing, it indicates there may be too little water in the appliance, a defective water shortage switch, a defective cable to the pump or water shortage switch, a blocked or defective pump, or the pump output is too low. Ensure adequate water supply and check the water shortage switch and pump.
Explains manual structure, safety symbols, and applicable documents for clarity.
Details CE marking compliance with EU directives for gas appliances and EMC.
Comprehensive technical specifications including heat output, dimensions, gas/water pressures, and electrical data.
Visual representation of the boiler's physical dimensions and component layout.
Guidelines for selecting an appropriate installation location considering clearances and environmental factors.
Procedures for ensuring a safe and compliant gas supply connection to the boiler.
Requirements for safe and compliant electrical connection, including fused supply and isolation.
Specifies essential clearances around the boiler for installation, operation, and servicing.
Detailed instructions for performing a safe and leak-free gas connection to the appliance.
Step-by-step guide for wiring the boiler, including main supply and control connections.
Procedures for filling and venting the heating system, ensuring correct pressure and water flow.
Steps to verify gas inlet pressure and rate, crucial for safe and efficient boiler operation.
Essential checks to perform after installation to ensure the boiler operates correctly.
Guidance on instructing the user on safe operation, controls, and maintenance.
Recommendations for preliminary checks before performing any servicing tasks.
Overview of regular maintenance tasks required for optimal boiler performance and longevity.
Detailed instructions for the removal, servicing, and refitting of the burner module.
A systematic guide to diagnose and resolve issues before referring to fault codes.
Explanation of various status codes displayed by the boiler, indicating operational states.
Details on accessing and interpreting diagnostic codes for advanced fault analysis.
Critical safety precautions to be followed before undertaking any component replacement.
Step-by-step guide for the safe removal and replacement of the burner.
Procedures for replacing the boiler's electronic control board and display unit.
General| Model | ecoTEC plus 615 |
|---|---|
| Category | Boiler |
| Output | 15 kW |
| Dimensions (H x W x D) | 720 x 440 x 338 mm |
| Fuel Type | Natural Gas |
| Mounting | Wall-mounted |
| Max. Working Pressure | 3 bar |
| NOx Emissions Class | 5 |
| Flue Options | Horizontal and Vertical |
| Heating Flow Temperature Range | 30°C to 80°C |
| Efficiency | 94% ErP |
To Next Page
