What to do if the water pressure sensor or cable harness hydraulics are defective in my Vaillant ecoTEC plus 615?
If the water pressure sensor or cable harness hydraulics are defective in your Vaillant Boiler, it could be due to a broken line to the water pressure sensor, a short-circuit at 0 V, or a defective water pressure sensor. Inspect and replace the water pressure sensor or repair the line.
Why is there a short circuit in the return-NTC of my Vaillant ecoTEC plus 615?
A short circuit in the return-NTC of your Vaillant Boiler is often due to a defective NTC. Inspect and replace the NTC if defective.
What to do if there is a short circuit in the flow-NTC of my Vaillant ecoTEC plus 615?
If there is a short circuit in the flow-NTC of your Vaillant Boiler, it could be due to the NTC plug shorted to the casing or a defective NTC. Inspect and replace the NTC if defective.
What does EEPROM error mean in my Vaillant Boiler?
An EEPROM error indicates that the electronics are defective. Replace the defective electronics.
What to do if my Vaillant Boiler shows flow and/or return NTC fault?
If there is a flow and/or return NTC fault, the flow and/or return NTC is defective (tolerances too big). Replace the flow and/or return NTC.
What to do if my Vaillant ecoTEC plus 615 Boiler has no communication to mainboard?
If there is no communication to the mainboard, there might be a connection error between the display and the mainboard. Check the connections to the mainboard.
Why is there a large temperature spread in my Vaillant ecoTEC plus 615?
A large temperature spread between the flow and return probe in your Vaillant Boiler, indicating a water shortage, can be caused by a blocked or defective pump, or the pump output being too low. Inspect and repair or replace the pump.
What causes rapid temperature rise in my Vaillant Boiler?
A rapid temperature rise in your Vaillant Boiler, indicating a water shortage, can be caused by a blocked pump, insufficient pump output, air in the appliance, low plant pressure, or interchanged flow and return NTCs. Inspect system for air and correct pump issues.
Why does the flame go off during operation in my Vaillant ecoTEC plus 615 Boiler?
If the flame goes off during operation and subsequent ignition attempts fail in your Vaillant Boiler, it could be due to a temporarily stopped gas supply, spark failure in the ignition transformer, or faulty earthing of the appliance. Check gas supply and ignition system for faults.
What to do if my Vaillant ecoTEC plus 615 is dry firing?
If your Vaillant Boiler is dry firing, it indicates there may be too little water in the appliance, a defective water shortage switch, a defective cable to the pump or water shortage switch, a blocked or defective pump, or the pump output is too low. Ensure adequate water supply and check the water shortage switch and pump.
Explains manual structure, safety symbols, and applicable documents for clarity.
Details CE marking compliance with EU directives for gas appliances and EMC.
Comprehensive technical specifications including heat output, dimensions, gas/water pressures, and electrical data.
Visual representation of the boiler's physical dimensions and component layout.
Guidelines for selecting an appropriate installation location considering clearances and environmental factors.
Procedures for ensuring a safe and compliant gas supply connection to the boiler.
Requirements for safe and compliant electrical connection, including fused supply and isolation.
Specifies essential clearances around the boiler for installation, operation, and servicing.
Detailed instructions for performing a safe and leak-free gas connection to the appliance.
Step-by-step guide for wiring the boiler, including main supply and control connections.
Procedures for filling and venting the heating system, ensuring correct pressure and water flow.
Steps to verify gas inlet pressure and rate, crucial for safe and efficient boiler operation.
Essential checks to perform after installation to ensure the boiler operates correctly.
Guidance on instructing the user on safe operation, controls, and maintenance.
Recommendations for preliminary checks before performing any servicing tasks.
Overview of regular maintenance tasks required for optimal boiler performance and longevity.
Detailed instructions for the removal, servicing, and refitting of the burner module.
A systematic guide to diagnose and resolve issues before referring to fault codes.
Explanation of various status codes displayed by the boiler, indicating operational states.
Details on accessing and interpreting diagnostic codes for advanced fault analysis.
Critical safety precautions to be followed before undertaking any component replacement.
Step-by-step guide for the safe removal and replacement of the burner.
Procedures for replacing the boiler's electronic control board and display unit.
General| Model | ecoTEC plus 615 |
|---|---|
| Category | Boiler |
| Output | 15 kW |
| Dimensions (H x W x D) | 720 x 440 x 338 mm |
| Fuel Type | Natural Gas |
| Mounting | Wall-mounted |
| Max. Working Pressure | 3 bar |
| NOx Emissions Class | 5 |
| Flue Options | Horizontal and Vertical |
| Heating Flow Temperature Range | 30°C to 80°C |
| Efficiency | 94% ErP |
To Next Page
