Need help?Do you have a question about the Valet 551T and is the answer not in the manual?
General| Type | Car Alarm |
|---|---|
| Shock Sensor | Yes |
| Keyless Entry | Yes |
| Panic Mode | Yes |
| LED Indicator | Yes |
| Number of Buttons on Remotes | 4 |
| Number of Remotes Included | 2 |
| Remote Control | Yes |
| Door Trigger | Yes |
| Starter Kill | Yes |
| Valet Mode | Yes |
| Compatibility | Vehicles with standard electrical systems |
| Remote Control Range | 1500 ft |
Lists included components and provides an overview of the control module's connectors.
Covers installation, ventilation, user responsibility, carbon monoxide detectors, and avoiding starting in gear.
Details consequences of misuse, property damage, personal injury, death, and installer liability.
Specifies vehicle compatibility, tool requirements, and essential pre-installation steps.
Outlines essential post-installation tests and checks before final vehicle reassembly.
Details methods for finding and connecting to a constant 12V power source.
Provides step-by-step instructions for identifying the vehicle's starter wire.
Guides users on how to locate the 12V switched ignition wire using a multimeter.
Details how to identify accessory power wires, noting potential multiple accessory wires.
Explains how to locate the positive parking light wire, with notes on Asian vehicles.
Provides a method for testing the parking light wire for proper function.
Details how to locate the tachometer wire, warning against using test lights.
Explains how to identify the wait-to-start bulb wire in diesel vehicles.
Diagram detailing the connections for the 8-pin Primary Harness (H1).
Wiring diagram for the 5-pin Remote Start Ribbon Harness.
Diagram illustrating the wiring for the heavy gauge relay satellite.
Diagram for the 6-pin Remote Start Harness (H2).
Detailed guide for connecting the Primary Harness (H1) wires.
Details connecting the H1/2 WHITE/BLUE activation input wire.
Explains connecting the H1/3 disarm or special accessory output wire.
Guides connecting the H1/4 YELLOW ignition output to the RF system.
Details connecting the H1/5 WHITE light flash output.
Explains connecting the H1/6 GRAY/BLACK diesel wait-to-start input.
Details connecting the RED 12V input wires to the relay satellite.
Guide for connecting the PINK ignition output wire.
Explains connecting the ORANGE accessory output wire.
Details connecting the PURPLE starter output wire.
Instructions for connecting the PINK/WHITE second ignition output wire.
Details the H2/1 BLUE status or factory security rearm output.
Explains the H2/2 BLUE/BLACK third ignition output.
Guide for connecting the H2/3 GRAY hood pinswitch input.
Details connecting the H2/4 BROWN brake switch input.
Explains connecting the H2/5 VIOLET/WHITE tachometer input.
Details connecting the H2/6 BLACK/WHITE neutral safety switch input.
Explains the importance and methods of integrating the neutral safety switch.
Discusses using the key-in-ignition sense switch to prevent remote starting.
Details connecting H2/4 BROWN to prevent activation with key in run.
Lists vehicle models known to have mechanical neutral safety switches.
Wiring diagram for GM trucks, SUVs, and column-shifting passenger cars.
Wiring diagram for pre-1996 Dodge Dakota pickups with 2.5L engines.
Explains GM VATS and the use of optional resistors for bypassing.
Wiring diagram illustrating the procedure for bypassing GM VATS.
Details Passlock I and II systems found in General Motors vehicles.
Covers Passkey III and other transponder-based anti-theft systems.
Explains the anti-grind relay's purpose and provides wiring diagrams.
Describes the program switch and its connection to the unit.
Step-by-step guide for teaching the system the tachometer signal.
Explains the internal programming jumper and its settings.
Details how to enable or disable the digital tach threshold.
Step-by-step guide to accessing and programming operating settings.
Lists available features, default settings, and LED off settings.
Description of the engine checking feature and its operation.
Details Tach wire vs. voltage sense modes for engine monitoring.
Explains the programmable engine run time settings.
Describes parking light flashing vs. constant output options.
Details the adjustable crank time for starting the engine.
Explains HIGH/LOW voltage check level settings.
Details the auxiliary output for alarm disarm or special accessories.
Describes the blue wire's status or factory re-arm output.
Explains how activation pulses affect unit activation/deactivation.
Step-by-step guide to enter the shutdown diagnostics mode.
Lists LED flash patterns and their corresponding shutdown modes.
Explains how to enter and use the Timer Mode for scheduled starts.
Outlines essential safety tests before vehicle reassembly.
Troubleshooting steps for when the remote start fails to activate.
Steps to diagnose why the starter does not engage after activation.
Diagnosing why the vehicle starts and then immediately shuts down.
Troubleshooting for when the starter continues to run after the engine starts.
Diagnosing short run times for the remote start system.
Troubleshooting climate control issues during remote start operation.
Comprehensive diagram summarizing all harness connections.
To Next Page
