Valor H5 - User Manual

1
Note: This kit must be installed or serviced by a qualifi ed installer, service agency or gas supplier.
These instructions are to be used in conjunction with the main installation instructions for the above
listed models.
WARNING: If these instructions are not followed exactly, a fi re or explosion may result
causing property damage, personal injury or loss of life.
GROUNDING: This power supply must be installed and grounded in accordance with local codes,
or in the absence of local codes, with the current Canadian Electrical Code CSA C22.1. or in the
USA the National Electrical Code ANSI/NFPA70 latest edition.
Description of System
The models listed above have been designed to ac-
commodate the installation of an air circulation fan.
Operated via the remote control handset and having
variable speed control, the fan is designed to boost the
natural convection through the heater; this may be a
desirable feature dependent on the fi replace location
and room layout.
It is preferable to install the circulating fan before
completing the heater installation although it may
also be retrofi tted at a later date provided power has
been pre-wired within the fi replace casing.
Note: Live wiring must terminate within a junction box.
A junction box is supplied as part of this kit. If roughing-
in power ahead of the fan installation, ensure the wiring
is not live or terminate within a temporary junction box.
Retrofi tting the fan after the fi replace installation is
completed will require disconnecting the gas and
removing the burner module and gas train from the
fi replace.
The fan is designed for automatic operation to come
on and off when the burner comes on and off. The fan
speed can be controlled from the remote control hand-
set. There are four speeds available. The fan, if turned
on, will start approximately 4 minutes after lighting the
appliance and will continue to run for approximately 10
minutes after the burner is shut off. The fan will operate
at the speed last selected by the user.
1195CFK CIRCULATING FAN KIT
CSA approved for use only with Valor models 1100, 1150 and 1400 Series Heaters
4004422-03
© 2015, Miles Industries Ltd. All rights reserved.
Operation
To operate the fan, press the button on the remote
handset; the fan icon fl ashes on the display. Press
the and buttons to set the fan speed. No bar
showing means the fan is OFF. Press the button
to confi rm the setting or wait. The fan icon and number
of bars will show when the remote is in other modes to
confi rm the fan status.
Note: The fan, when plugged in, provides power for
the remote control receiver via the fan control module.
Therefore batteries are no longer required in the
receiver other than for back-up purposes. Batteries
are still required in the remote control handset.
Electrical Requirements
The fan kit requires a power supply of 120 Volts,
1 phase, 60 Hz. Full load current is less than 1 amp.
Installation and Operating Instructions
H5 & H6

Summary

Installation and Operating Instructions

Description of System

Details the circulating fan's purpose and variable speed operation via the remote handset.

Operation

Explains how to control the fan's speed and status using the remote handset.

Electrical Requirements

Specifies the necessary power supply voltage, phase, and frequency for the fan kit.

Fan Kits Components

Install the fan

Prepare Appliance and Install Junction Box

Covers unpacking, junction box installation, and initial wiring prep.

Remove Burner Assembly

Details how to safely remove the burner module and plate from the fireplace.

Route and Secure Wiring

Instructions for routing electrical wire and securing the junction box.

Fan Installation Continued

Connect Internal Wiring

Explains connecting wires within the junction box and appliance.

Mount Fan and Control Module

Covers installing the fan unit, control module, and wiring diagram label.

Reassemble Burner Plate

Instructions for re-installing the burner module plate.

Testing and Operation

Test Fan Functionality

Guides on how to test the fan's operation using the remote control.

Enable Fan Feature

Steps to enable the fan function if it is disabled on the remote.

Regular Fan Operation

Describes the automatic start and stop behavior of the fan during normal use.

Final Installation Steps

Re-attach Burner Plate

Instructions for re-installing the burner plate after fan installation.

Re-install Burner Assembly

Final steps for fitting and securing the burner assembly.

Complete Fireplace Setup

Refers to the main appliance manual for remaining installation tasks.

Wiring Diagram and Grounding

Electrical Grounding Instructions

Emphasizes proper grounding procedures for electrical safety.

Valor H5 Specifications

General

Brand	Valor
Model	H5
Category	Fan
Language	English