EasyManua.ls Logo

VEMAG HP25E - User Manual

VEMAG HP25E
189 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Vacuum ller
HP25E (from 1640800)
HP30E (from 1660917)
Operating instructions

Table of Contents

Questions and Answers

  • A
    Amber RichardsonAug 15, 2025
    Why are there weight fluctuations in my VEMAG Industrial Equipment?
    • A
      Anthony GriffinAug 15, 2025
      Weight fluctuations in VEMAG Industrial Equipment can arise from several factors. Ensure you're using the correct double screw, especially a 48 mm double screw pitch for smaller portions. Inspect the double screw and housing for wear, maintaining a maximum air gap of 0.5 mm. Close any air relief bores in the double screw housing. Verify the vacuum system's integrity. Finally, check the feed screw, ensuring a 110 - 120 mm gap between its bottom edge and the housing's top edge.
  • L
    lbarnesAug 18, 2025
    How to prevent air trapped in product with VEMAG Industrial Equipment?
    • O
      omercerAug 18, 2025
      If your VEMAG Industrial Equipment is experiencing air trapped in the product, several factors could be responsible. Begin by inspecting the double screws for wear or suitability. Next, check the vacuum system for leaks, focusing on the double screw drive seal. If the vacuum display fluctuates, it indicates air intake by the vacuum pump, so inspect the valve float. Clear any blocked air relief bores using the setting screws. Employ mixing speed during the final bowl-cutting phase and ensure the entire vacuum system is free-flowing.
  • K
    kennethrichardsonAug 21, 2025
    What to do if raw sausage smears with VEMAG Industrial Equipment?
    • D
      Dr. Theresa Lin MDAug 21, 2025
      If you notice raw sausage smears when using your VEMAG Industrial Equipment, it could be due to several reasons. First, ensure that you are using the appropriate double screw. Check the product feed for any lumps. Inspect the vacuum system for any issues. Finally, consider reducing the product temperature.
  • C
    Carl TaylorAug 25, 2025
    Why is there a drop in output from my VEMAG HP25E Industrial Equipment?
    • T
      Timothy SparksAug 25, 2025
      A drop in output in your VEMAG Industrial Equipment may be caused by worn double screws and housing, a low vacuum, or a deformed feed screw. Inspect the double screw and housing for wear, measuring the air gap. Ensure the vacuum setting is correct, with no product in the vacuum pot. Check the feed screw, maintaining a 110 - 120 mm gap between its bottom edge and the housing's top edge.
  • J
    Justin SmithAug 28, 2025
    What to do if the lifting/tipping device (optional) is not functioning on VEMAG HP25E?
    • P
      Pamela KingAug 28, 2025
      If your VEMAG Industrial Equipment's lifting/tipping device isn't working, it could be due to several reasons. The buttons might not be responding, or the valve Y1, Y2 isn't being actuated or is defective. The hoist motor could also be malfunctioning, or the power switch QM5 might have been triggered. Check the hoist motor and switch on the power switch. For the valve issue, check the voltage indicated by the LED below the valve plug. For further assistance, contact VEMAG Customer Service.
  • S
    Samantha PalmerAug 31, 2025
    How to solve machine temperature too high in VEMAG Industrial Equipment?
    • A
      Alyssa JonesSep 1, 2025
      If your VEMAG Industrial Equipment machine temperature is too high, the air filter might be contaminated. Clean the air filter to resolve this issue.
  • J
    jaymcdonaldSep 4, 2025
    What to do if vacuum level not reached, vacuum unstable in VEMAG HP25E Industrial Equipment?
    • M
      marytorresSep 4, 2025
      If the vacuum level is not being reached or is unstable in your VEMAG Industrial Equipment, there could be a leak in the vacuum system. Also, water or product residues might be in the line to the display, or the air de-oiling element could be contaminated. Check the vacuum system for leaks. Clean or replace the line if necessary. Replace the air de-oiling element.
  • M
    Michael JenkinsSep 7, 2025
    Why display does not light up on VEMAG HP25E Industrial Equipment?
    • J
      joshuapetersonSep 7, 2025
      If the display on your VEMAG Industrial Equipment does not light up, several issues could be the cause. There might be no mains voltage, or the main switch might not be turned on. Additionally, fuses F1, F2, or F3 could be defective, or the power supply or graphic control could be malfunctioning. Switch on the main switch. Have machine back-up fuse replaced by an electrician. Have fuse replaced by an electrician. Have defective part replaced by electrician.
  • K
    Kimberly RogersSep 10, 2025
    Why is the vacuum pump not running on my VEMAG Industrial Equipment?
    • B
      Bobby BautistaSep 10, 2025
      If the vacuum pump isn't running on your VEMAG Industrial Equipment, the power switch QM4 may have been triggered, or the vacuum pump could be overloaded. Switch on the power switch. Check the vacuum pump.

Summary

Vacuum Filler Operating Instructions

Foreword

Introduction to the manual and machine overview, including versions and support contact.

Safety Instructions

Essential safety guidelines, symbols, and warnings for safe operation and hazard avoidance.

Machine Description

Overview and detailed description of machine components and their functions.

Installation and Commissioning

Steps for transporting, setting up, and connecting the machine for initial operation.

Setting Up the Machine

Procedures for assembling and preparing machine parts for operation.

Machine Operation

Procedures for starting, running, and finishing production cycles.

Graphical Control System

Explanation of the machine's interface, screen layout, and controls.

Service and Information

System service information, error messages, and troubleshooting guidance.

Cleaning Procedures

Guidelines and steps for cleaning machine parts and the entire unit.

Maintenance Schedule

Periodic maintenance tasks and intervals for optimal performance and longevity.

Troubleshooting Guide

Common faults, their causes, and recommended remedies for machine issues.

Appendix and Technical Data

Supplementary information, technical specifications, and spare parts details.

VEMAG HP25E Specifications

General IconGeneral
BrandVEMAG
ModelHP25E
CategoryIndustrial Equipment
LanguageEnglish

Related product manuals