VEVOR S3018 Prover - User Manual

1/12
S3018 Prover CNC Engraving Machine
Catalog
1. Part List…………………………………………………………………...…2
2. Machine Assembly………………....................................................3
3. Candle Software………………………………………………......…......8
4. Offline Controller ……………………………………………..……..…11
5. Restore factory settings…….……………….................................12
6. Online guide and video……..……………….................................12
Safty Notice
Avoid direct laser radiation on eyes or skin
Away from children
Always wear protective glasses when use the laser
Prohibited from use in flammable objects or gases
Please cut off the power immediately in case of emergency
Shutdown steps: first cut off the power, then pull out the USB cable
Precautions
(1). All parts description just for illustrative purpose. If there is any difference, please refer to the actual part shape.
(2). Please make sure that the machine is under care when it is working.
(3). If your machine is equipped with an offline controller, please note that the offline controller and the computer
cannot be connected to the engraving machine at the same time, otherwise it will not work normally.
(4). If the U disk in the machine kit can't be read, please scan the QR code to see how to download the software and
related content.
Scan for videos and guides

Summary

Parts List

Optional Packages

Lists optional components for the CNC machine, including laser kits and protective glass.

Guard Plate Components

Details the specific parts required for the assembly of the guard plate.

Safety and Limit Switch Components

Lists parts for the emergency stop functionality and limit switches.

Control Board Components

Details the various components that make up the main control board assembly.

Fixture Assembly Parts

Specifies the parts needed for assembling the fixture, including screws and nuts.

Offline Controller Components

Lists the parts associated with the optional offline controller.

Machine Assembly

X-axis and Y-axis Assembly

Instructions for assembling the X and Y axis components of the machine.

Control Board and Emergency Stop Assembly

Steps for installing the control board and emergency stop switch.

Y-limit Switch and Rubber Mat Assembly

Details the assembly of the Y-limit switch and rubber mat.

Guard Plate Assembly

Guide for installing the guard plates on the machine.

Control Board Wiring Diagram

Wiring Connections Overview

Illustrates the connections between the control board, axes, motors, and other components.

Candle Software Guide

Understanding Machine States

Explains the different states of the CNC machine in the software.

Software Control Functions

Describes the various control buttons and functions within the Candle software.

Software Installation and Setup

Guides through driver installation, port setup, and connection.

Importing and Visualizing G-Code

Details how to load, view, and process G-code files in the software.

Fixture, Tool Installation, and Zeroing

Explains fixture setup, tool installation, and setting the work origin.

Starting the Carving Process

Instructions on how to initiate the engraving or carving operation.

Completing the Carving Process

Information on what happens after the carving process is finished.

Offline Controller Operation

Offline Controller Main Page

Overview of the main interface and button functions of the offline controller.

Offline Controller Axis Control

Details how to manually control the machine axes using the controller.

Offline Controller File Management

Explains how to select and manage engraving files on the controller.

Confirming Engraving Job

Process for confirming the selected engraving file before starting.

Offline Controller Settings

How to adjust settings like baud rate and feed rate on the controller.

Offline Controller WiFi Connectivity

Information on connecting the controller to WiFi for file management.

Restore Factory Settings

Factory Reset via VigoWorks Software

Method to restore factory settings using the VigoWorks software.

Factory Reset via Candle Software

Method to restore factory settings using Candle software commands.

Assembly Video and Online Resources

Accessing Assembly Video and Guides

Instructions on how to access assembly videos and download related software/documents via QR codes.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The VEVOR S3018 Prover CNC Engraving Machine is a versatile tool designed for precision engraving and milling, controlled by GRBL-based software. This machine is suitable for various applications, from hobbyist projects to more intricate professional tasks.

Function Description:

The S3018 Prover operates as a GRBL-based CNC machine, supporting G-code file processing and visual display. It allows users to engrave and mill materials with high accuracy. The machine can be controlled via console commands, on-form buttons, or a numpad, offering flexible operation. It monitors the CNC machine's state, enabling users to load, edit, save, and send G-code files, as well as visualize the G-code paths.

The machine's core function is to translate digital designs into physical engravings or cuts. It utilizes a three-axis coordinate system (X, Y, Z) for precise tool movement. The spindle motor, with a power range of 0-500W, drives various milling cutters to perform the desired operations. Optional components like a laser kit expand its capabilities to include laser engraving.

Important Technical Specifications:

• Control Board: VIGOTEC control board.
• Power Supply: 24V, 5A.
• Stepper Motors: Controlled by 4-pin wires (X/Z axis: 480mm length, Y1 axis: 150mm length).
• Spindle Motor: 2-pin wire, 480mm length, 0-500W power.
• Limit Switches: X-limit, Y-limit (2PCS), Z-limit (2PCS) for precise homing and boundary detection.
• Emergency Stop Switch: Included for safety.
• Connectivity: USB cable for computer connection.
• Offline Controller (Optional): 1.8 inches with SD card, allowing standalone operation without a computer.
• Laser Kit (Optional): Includes laser kit, 3P laser wire, and protective glass.
• Guard Plate (Optional): Two guard plates with M5*10 screws and M5-10 ship nuts for enhanced safety.
• Fixture Assembly: Consists of pressing plates (50203), M640 and M645 screws, M6 butterfly nuts, and M6*2mm washers.
• Working Area: The Y-axis component is 50mm wide.
• Cable Lengths:
  • Z1/Z2-Limit wire: 2.0-2.54, 600mm length.
  • X/Y2-Limit wire: 2.54-3P, 600mm length.
  • Y1-Limit wire: 2.54-3P, 300mm length.

Usage Features:

• Software Control: Primarily uses Candle software, an open-source GUI for GRBL-based CNC machines. It provides a visualizer for G-code and allows for comprehensive control.
• States Monitoring: The software displays work coordinates (current X, Y, Z local coordinates) and machine coordinates (absolute machine coordinates). It also shows the CNC status, such as Idle, Running, Home, Check, Hold, or Alarm.
• Control Functions:
  • Home Button: Initiates the homing cycle ($H command).
  • Z-probe: Starts the zero Z-axis search procedure (e.g., G91G21; G38.2Z-30F100; G0Z1; G38.2Z-1F10).
  • Zero X/Y: Resets X and Y coordinates in the local system, retaining a local system offset (G92).
  • Restore X/Y/Z: Restores local system coordinates with G92.
  • Safe Z: Moves the tool to a safe Z-position, configurable in machine coordinates.
  • Reset: Resets the CNC with CTRL+X.
  • Unlock: Unlocks the CNC with $X.
• Driver Installation: Requires CH340-Driver.exe installation for first-time use, though Win10 systems may auto-install.
• Port and Connection Setup: Users must select the correct COM port and set the baud rate (typically 115200) in the Candle software settings.
• File Processing: Supports various G-code file formats (NC, NCC, TAP, TXT, Gcode, GCO, NL, CUT, CNC). Users can load, edit, and send files for engraving.
• Fixture and Tool Installation: The product kit includes four sets of fixtures for securing materials. The ER11 collet on the spindle motor must be properly clamped, and cutters should not extend too far.
• Working Coordinate Origin: Before engraving, users must define the engraving figure's position relative to the overall engraving plate. The X, Y, and Z axes can be reset to zero after positioning the tool near the material surface (e.g., one sheet of paper distance for engraving).
• Offline Controller: Allows operation without a computer. It features a main page for basic control, a control page for manual axis movement, a file page for selecting engraving files from an SD card, a confirmation page for starting engraving, and a settings page for adjusting baud rate and feed rates.
• WiFi Network (Offline Controller): The offline controller can establish a WiFi hotspot (VIGO-STK****) or connect to a local WiFi network (2.4G signal only). This enables file management (upload/delete) via a web browser (192.168.0.1 or vigostick.local).

Maintenance Features:

• Restore Factory Settings: If the machine experiences issues like stuck engraving movements or non-moving stepper motors, users can restore factory settings. This can be done via VigoWorks software (downloadable from www.VevorEngraver.com) by clicking "Restore Factory" in the settings, or by sending the command "$RST=*" through Candle software, followed by a machine reboot.
• Safety Precautions:
  • Avoid direct laser radiation to eyes or skin.
  • Keep away from children.
  • Always wear protective glasses when using the laser.
  • Do not use in flammable objects or gases.
  • Immediately cut off power in case of emergency.
  • Shutdown steps: first cut off power, then pull out the USB cable.
  • Ensure the machine is supervised during operation.
  • If equipped with an offline controller, do not connect both the controller and a computer to the engraving machine simultaneously.
  • If the U disk is unreadable, scan the QR code for software and content downloads.

VEVOR S3018 Prover Specifications