What to do if my Victron Energy Controller charger does not function?
If the Victron Energy Controller charger isn't working, check the PV connection; a reversed connection can cause this, so connect it correctly. Also, verify that a 20A fuse is properly inserted.
Why is my Victron energy BlueSolar MPPT 75/10 Controller battery not fully charged?
Several factors can prevent your Victron Energy Controller battery from fully charging. Check the battery connection. High cable losses can occur, so use cables with a larger cross-section. A large ambient temperature difference between the charger and battery can be the reason, so ensure equal ambient conditions for both. For 24V systems, confirm the correct system voltage (24V instead of 12V) is selected by disconnecting PV and battery, ensuring the battery voltage is >19V, and then reconnecting properly.
Why is my Victron energy BlueSolar MPPT 75/10 battery being overcharged?
If your Victron Energy Controller battery is being overcharged, it could be due to a defect in a battery cell; if this is the case, replace the battery. Another cause may be a large ambient temperature difference between the charger and battery; ensure that ambient conditions are equal for both.
Why Victron Energy Controller charger does not function?
The Victron Energy Controller charger might not be functioning due to a reversed PV connection. In this case, connect the PV correctly. Another cause may be that no fuse is inserted; make sure to insert a 20A fuse.
What to do if the Victron Energy Controller battery is not fully charged?
If the Victron Energy Controller battery isn't fully charged, check the battery connection, as a bad connection can be the cause. High cable losses can also prevent a full charge, so use cables with a larger cross-section. Ensure that ambient conditions are equal for charger and battery because a large ambient temperature difference between charger and battery can affect charging. Finally, if you have a 24V system, make sure that the charge controller is set to the required system voltage (24V instead of 12V).
What to do if the Victron energy BlueSolar MPPT 75/10 battery is being overcharged?
If the Victron Energy Controller battery is being overcharged, it could be due to a defect in one of the battery cells; if this is the case, replace the battery. Another possible cause is a large ambient temperature difference between charger and battery. To solve this, make sure that ambient conditions are equal for charger and battery.
What to do if my Victron Energy Inverter load output does not become active?
If the load output on your Victron Energy Inverter doesn't activate, it could be due to several reasons. First, ensure that the output current doesn't exceed the maximum limit of 15A. Also, if you're using a DC load with a capacitive load (like another inverter), disconnect the DC load during the start-up of the capacitive load. Alternatively, disconnect the AC load from the inverter. Finally, check the load connection for any short circuits.
What to do if Victron energy BlueSolar MPPT 75/10 Controller load output does not become active?
If the load output on your Victron Energy Controller doesn't activate, it might be due to exceeding the maximum current limit; ensure the output current doesn't exceed 15A. It could also be a DC load with a capacitive load (like an inverter) applied; in this case, disconnect the DC load during the inverter's start-up, or disconnect the AC load from the inverter. Check the load connection for a short-circuit.
What causes a blown fuse in Victron energy BlueSolar MPPT 75/10?
A blown fuse in the Victron Energy Controller is often caused by a reversed battery connection. To solve this, connect the battery correctly and replace the fuse.
How to fix Victron energy BlueSolar MPPT 75/10 Controller load output not becoming active?
If the load output on your Victron Energy Controller isn't activating, it might be due to exceeding the maximum current limit. Ensure the output current doesn't exceed 15A. Another reason might be using a DC load in combination with a capacitive load (like an inverter). Disconnect the DC load during the start-up of the capacitive load. Check the load connection for a short-circuit.
General| Model | BlueSolar MPPT 75/10 |
|---|---|
| Category | Controller |
| Technology | MPPT |
| Maximum PV Open Circuit Voltage | 75V |
| Maximum PV Power (12V) | 145W |
| Maximum PV Power (24V) | 290W |
| Maximum Charge Current | 10A |
| Nominal Battery Voltage | 12/24V Auto Select |
| Humidity | 95%, non-condensing |
| Communication Port | VE.Direct |
| Efficiency | Up to 98% |
| Protection | Over Temperature |
| Operating Temperature Range | -30°C to +60°C |
Covers essential safety guidelines for product installation, operation, and maintenance.
Details on using appropriate cables and ensuring safe electrical connections for the charger.
Explanation of safety symbols found on the solar charger's casing.
Overview of the charger's capabilities regarding system voltage and current.
Explains how the charger automatically identifies the connected battery system voltage.
Details the advanced Maximum Power Point Tracking technology for optimal energy harvest.
Highlights the high efficiency of the solar charger and its benefits.
Describes the built-in protection mechanisms against various electrical faults.
Introduction to the mobile app for monitoring, configuration, and firmware updates.
Overview of available display options for monitoring charger status and data.
Information on the communication port for connecting external devices.
Details the physical and virtual load outputs for powering connected devices.
Explanation of the adaptive 3-stage charging process and flexible algorithms.
Describes how temperature sensing affects charging voltage for optimal battery health.
Explains voltage sensing for compensating charge voltage losses.
How to remotely control the charger's operation using a dedicated cable.
Information on the optional WireBox accessory for enhanced safety.
Instructions and guidelines for physically installing the solar charger.
Details on battery protection requirements, including fuse ratings.
Guidance on connecting the solar panel array, including voltage and configuration.
Information on proper grounding procedures for the system and chassis.
Diagram and explanation of the charger's terminal connections.
Step-by-step guide for making electrical connections to the charger.
Instructions for connecting an optional external display unit.
Overview of methods available for configuring the solar charger settings.
Detailed explanation of each user-configurable setting within the charger.
Procedure for checking and updating the charger's firmware via the VictronConnect app.
Information on creating wireless networks for data sharing between Victron devices.
Steps and conditions for powering up the solar charger.
Explanation of the battery charging process, including lead-acid algorithms.
Details on enabling and configuring automatic equalization for specific battery types.
Specific charging settings and considerations for Lithium Iron Phosphate batteries.
Correct steps for safely shutting down and restarting the solar charger.
Information regarding the maintenance requirements for the solar charger.
Explanation of the status LEDs and their meaning during operation and faults.
Overview of error codes displayed by the charger and how to interpret them.
Guide to accessing live data, history, and errors using the VictronConnect app.
How to monitor the charger remotely through GX devices and the VRM portal.
Procedure for visually inspecting the charger for physical damage before troubleshooting.
Steps to diagnose and resolve issues where the charger shows no activity.
Troubleshooting common reasons why the solar charger may stop operating.
Explains normal behavior when the charger is governed by an external system.
Diagnosing scenarios where the charger is active but batteries are not charging.
Identifying causes and solutions for batteries not reaching full charge.
Troubleshooting steps for preventing and addressing battery overcharging.
Reasons why the charger may not reach its maximum rated power output.
Common problems and solutions related to Bluetooth, VE.Direct, and VE.Smart networking.
Diagnosing problems with the load output not functioning as expected.
Addressing less common issues not covered in other troubleshooting sections.
Comprehensive list and explanation of error codes generated by the charger.
Detailed technical data and ratings for all supported charger models.
Physical dimensions and mounting details for the solar charger units.
To Next Page