How to prevent Viking Dishwashers dishes from breaking?
To prevent dishes from breaking in your Viking dishwasher, make sure to load the dishwasher as suggested in the manual and avoid overloading the racks, as dishes may hit each other and break.
How to fix Viking FDW103 Dishwasher that does not start?
To address the issue of your Viking Dishwasher not starting, check if the machine is properly plugged in and all fuses are working. Ensure the water supply is fully turned on and the dishwasher door is securely closed. Also, verify that you have pressed the On/Off button.
What to do if Viking FDW103 has water inside after rinse cycle?
To resolve the issue where water remains inside the Viking Dishwasher after the rinse cycle, clean all filters as described in the manual and ensure that the drain hose is properly placed and open.
Why are my Viking Dishwashers dishes not clean?
Several factors can cause your Viking dishwasher to not clean dishes properly. Ensure you are loading the dishwasher correctly as described in the manual and selecting a program that washes at a higher temperature or runs for a longer duration. Check that the spray arms are not blocked, the filters are clean and correctly positioned, and the spray arm nozzles are not clogged. Avoid overloading the racks. Make sure your detergent isn't moist or clumping, and use the proper amount of detergent and rinse agent. Also, ensure the detergent dispenser lid closes properly. Finally, note that cutlery with a worn surface quality isn't suitable for dishwashers.
How to dry dishes in Viking FDW103?
To fix dishes that are not drying in your Viking Dishwasher, ensure you are loading the dishwasher as suggested in the manual. Increase the dosage of rinse agent or refill the rinse agent dispenser if the supply is insufficient. Avoid emptying the dishwasher immediately after washing; instead, open the door slightly to let steam escape and wait until the dishes are only hand warm before unloading, starting with the lower rack. Select a program with a longer washing time, as shorter programs may have lower wash temperatures. Also, note that cutlery with a worn surface may not be suitable for dishwashers.
What to do if Viking FDW103 has rust stains?
To address rust stains or surface destruction in your Viking Dishwasher, check that the salt container lid is firmly closed and use a funnel to pour in special salt, running the Rinse and Hold program afterward. Ensure proper grounding of the system to prevent static electricity damage. Remove coarse dirt from dishes before washing and run the Rinse and Hold program every two days without detergent. Avoid washing low-grade rust-free steel cutlery or dish items with existing rust stains, as these are not suitable for dishwashers.
How to fix Viking Dishwashers door that won't stay open?
If the door of your Viking dishwasher won't stay down in the open position, adjust the door spring tension. Note that this applies to custom panel models only; refer to the Installation Guide for instructions.
Why are my dishes not clean in my Viking FDW103 Dishwasher?
To address dishes not being clean in your Viking Dishwasher, ensure proper loading as described in the manual, select a program with a higher temperature or longer wash time, and check that the spray arms are not blocked. Also, clean all filters and ensure they are correctly positioned. Clear any clogged spray arm nozzles, avoid overloading the racks, and store detergent in a dry location. Use the correct amount of detergent and rinse agent, close the detergent dispenser lid properly after filling, and avoid washing cutlery with worn surfaces.
Why do my glasses have a milky appearance in my Viking Dishwashers?
A milky appearance or rainbow effect (glass corrosion) on glasses washed in your Viking dishwasher can result from using too much detergent when the water hardness is low. Try using less detergent. If your water hardness is below 7 degrees, do not use salt, even if your dishwasher has a water softener.
Why does detergent residue remain in my Viking Dishwashers dispenser?
Detergent residue in your Viking dishwasher's dispenser can occur for several reasons. Ensure the dispenser is dry before filling it and add detergent just before washing. Avoid blocking the dispenser lid with large items. Store detergents properly in a dry location with the lid closed. Clean the spray arms if nozzles are clogged and ensure the spray arms can rotate freely. Also, terminating the cycle early can leave residue.
General| Control Type | Electronic |
|---|---|
| Capacity | 10 place settings |
| Wash Cycles | 6 |
| Energy Star Rated | Yes |
| Place Settings | 10 |
| Programs | 6 |
| Delay Start | Yes |
| Half Load Option | Yes |
To Next Page
