What to do if the Vingtor Marine Equipment system has shut down?
If the entire Vingtor Marine Equipment system has shut down and there's no light indication on the ETB panel, first check the voltage on terminal block K11 no.1-2. If there's no voltage, inspect the 24V DC mains power supply or the SPS-4 power supply. If the voltage measures correctly between 24-32VDC, check the S1 2AT and S2 1AT fuses.
How to troubleshoot SPS-4 power supply failure in Vingtor Marine Equipment?
To troubleshoot an SPS-4 power supply failure in Vingtor Marine Equipment, start by checking the main power supply to ensure 230V AC or 115V AC hasn't failed, switching the system to 24V DC emergency power. Also, check the 5.0AT fuse on terminal 3. If the problem persists, the power supply module may need repair or replacement.
How to reduce high background sound in Vingtor Marine Equipment?
If you are experiencing high background sound in your Vingtor Marine Equipment, and it's due to a nearby substation, consider replacing the current substation with one that uses a headset or an external loudspeaker STB-2. You can also adjust the master volume lines 1-5 in ETB-5 or 6-10 in ETB-10.
What to do if there is no signal in the Vingtor Marine Equipment substation?
If there's no signal in the substation when using the SIGN button in the ETB central unit, first disconnect the substation to check for a 1 KHz tone. If 7V AC is measured on terminals 1-2 in the ETB central unit, the unit is likely OK. If no voltage is measured, the ETB central unit may need repair. If no voltage is measured on terminals 1-2 in the substation after connecting it, the fault might be in the cable, or the substation might require repair.
How to fix system generated noise in Vingtor Marine Equipment?
To address system-generated noise in Vingtor Marine Equipment, begin by inspecting all cable connections, paying special attention to the screens, ensuring they meet the requirements. If the issue continues, try using a 1uF capacitor between terminals no. 1-2 block K11. If the problem still persists after these steps, it may require professional service.
Why is there no signal in the additional signal device of Vingtor Marine Equipment?
If there's a signal in the substation but none in the additional signal device when using the SIGN button, first disconnect the substation. If no voltage is measured on terminals 3-4 in the ETB central unit, check fuse S2 1A. If fuse S2 1A is OK, check the automatic fuse by waiting 2-3 seconds; if 24V DC is measured, the load is likely too high (exceeding 50 mA).
What to do if one Vingtor Marine Equipment substation cannot be operated?
If one substation of your Vingtor Marine Equipment cannot be operated, check the cable and terminal block in the ETB panel for the current extension. Also, inspect the cable and terminal block in the substation or plugbox. You can also try moving the terminal block to another extension number; if operation is OK on the new extension, the substation may need repair.
Why the Vingtor Marine Equipment substation cannot be operated?
If a Vingtor Marine Equipment substation cannot be operated, and there's no flashing green LED or signal in the ETB monitor loudspeaker for the selected line, first check the cable and terminal block in the substation or plugbox. Try moving this terminal block to another extension number; if the problem persists, the substation may need repair. If substation operation is OK, the ETB central unit may need repair.
How to fix operation problem from a Vingtor Marine Equipment substation?
To resolve an operation problem from a Vingtor Marine Equipment substation, try changing the polarity in substation terminals no. 1-2.
How to troubleshoot operation problems from a parallel station in Vingtor Marine Equipment?
If operation from a parallel station cannot be done on your Vingtor Marine Equipment, but it is possible from the ETB central unit, check the cable and connections between the parallel station and the ETB central unit. Also, check the microphones. If the problem persists, the parallel station may need to be repaired.
Description of components like loudspeaker, line buttons, LED indicators, microphone connector, and volume controls.
Steps for initiating and terminating a call to a substation using line, SIGN, and TALK buttons.
Instructions for making calls to multiple substations simultaneously using line buttons and TALK function.
Steps for broadcasting a message to all substations using the ALL button and microphone.
Procedure for making handsfree calls from the ETB central unit using a gooseneck microphone and foot switch.
Guidance on how to answer incoming calls, indicated by flashing LEDs and beeping sounds.
Instructions for distributing audio from external systems to substations and the central unit.
Steps for initiating Emergency Public Address announcements from different call station models.
Instructions for establishing parallel communication between stations using line buttons and TALK function.
General| Brand | Vingtor |
|---|---|
| Model | ETB-5 |
| Category | Cell Phone |
| Language | English |
To Next Page
