Need help?Do you have a question about the Vislink Lynx L2174 and is the answer not in the manual?
Details the manual version history and release dates for the product.
Specifies the firmware version on which the manual's content is based.
Provides contact information for technical support and service inquiries.
Outlines essential safety measures for equipment operation, grounding, and maintenance.
States compliance with EU directives and harmonised standards for radio equipment.
Describes the main hardware components and their interconnections within the L2174 receiver.
Details supported modulation modes, bandwidths, and general performance criteria.
Lists supported video and audio formats, resolutions, and bit depths.
Summarizes the various input and output connections available on the unit.
Specifies the physical dimensions, weight, operating temperature, and power requirements.
Describes the 75 Ohm BNC connectors for RF signal input (70MHz-860MHz).
Details the ASI input connector, its compliance, and function.
Explains the BNC connector for locking decoder output to SD or HD video sync signals.
Details the BNC connectors for HD SDI or SD SDI/CVBS video output.
Describes the ASI output connector for chaining or external decoding.
Outlines the LEMO connector for RS232 data and serial remote control.
Describes the XLR connectors for analogue and digital (AES) audio output.
Details the LEMO connectors for analogue and digital (AES) audio output.
Explains the LEMO connector for camera control and status feedback.
Describes the Ethernet port for web browser and SNMP control.
Details the Ethernet port for streaming encapsulated Transport Streams.
Describes the function of the MENU and ESCAPE keys for navigation.
Explains how to navigate menus using arrow keys and confirm/abort actions.
Details the function of the STATUS and MODE keys for quick access to menus.
Explains the indicators for STATUS, POWER, and LOCAL/REMOTE status.
Describes the USB port for firmware code updates.
Overview of menus for configuring demodulator settings like input mode and setup.
Allows selection of the modulation scheme (DVB-T, LMS-T).
Configures frequency, bandwidth, guard interval, and polarity for demodulation.
Selects downconverter type, power, and LO frequency for RF inputs.
Explains the optional deinterleaving feature for error correction.
Details menus for configuring decoder settings and service selection.
Allows selection and configuration of incoming services for decoding.
Configures the output mode for the video connectors, including overlays.
Selects the output format for audio channels (analogue or AES digital).
Contains options for video mode, loss behavior, frame lock, and pixel offset.
Manages descrambling modes and key entry if licensed.
Enables extraction of embedded data and displays baud rate and parity.
Displays PIDs for audio channels and other stream identifiers.
Controls transport stream handling, routing, and source selection.
Configures packet diversity and selects the source for transport streams.
Provides access to unit configuration, diagnostics, and interface settings.
Allows saving and recalling up to 16 configuration presets.
Restores the unit to its factory default settings.
Displays detailed performance information for Demodulator, Decoder, Unit, and System.
Configures external control interfaces like Web Identifier and Ethernet port settings.
Displays module versions and allows dumping configuration to USB.
Provides contact information and unit configuration details for support.
Enters license codes to enable features and displays licensed functionality.
Sets the unit's time and date, and displays accumulated run-time.
Tests front panel LEDs, adjusts display contrast, and initiates a unit restart.
Allows remote control of connected L1255 Data Transmitters.
Indicates input baud rate and CC serial data transmission status.
Indicates receiver lock status to a remote WCT.
Configures CCU options to indicate data transmission or return data presence.
Guides on connecting and using the web browser interface for unit configuration.
Displays a block diagram of the unit's routing and allows configuration of transport stream paths.
Describes how to configure various parameters via the web interface tabs.
Performs a thorough self-test on RF inputs and critical components.
Details the operating modes for the demodulator (DVB-T, LMS-T).
Provides the sequence for configuring DVB-T operation settings.
Provides the sequence for configuring LMS-T operation settings.
Explains the sequence for selecting down converter and receiver RF frequency.
Lists the different operating modes for the decoder.
Explains deinterleaving settings, FEC, and burst duration.
Details decryption options and key entry for licensed units.
Allows configuration of third-party down converters and LO frequencies.
Explains how to purchase and enter licenses for additional features.
Guides on upgrading the unit's firmware via the USB port.
To Next Page
General
