EasyManuals Logo

Visonic POWERMAXPRO User Manual

Visonic POWERMAXPRO
46 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #25 background imageLoading...
Page #25 background image
SPECIAL FUNCTIONS
24 D-302542
Command Individual Partition SMS
Format
All Partitions SMS format /
Partition Disable
1 Arm AWAY
"P# AWAY <code>"
"P# AW <code>"
"AWAY <code>"
"AW <code>"
2 Arm AWAY instant
Not supported command "AWAY INST <code>"
"AWI <code>"
3 Arm AWAY Latchkey
Not supported command "LATCHKEY <code>"
"LK <code>"
4 Arm AWAY Latchkey instant
Not supported command "LATCHKEY INST <code>"
"LKI <code>"
5 Arm HOME
"P# HOME <code>"
"P# HM <code>"
"HOME <code>"
"HM <code>"
6 Arm HOME instant
Not supported command "HOME INST <code>"
"HMI <code>"
7 Disarm
"P# DISARM <code>"
"P# DA <code>"
"DISARM <code>"
"DA <code>"
8 Turn light xx on
(xx = 01 – 15)
"LIGHT xx ON <code>"
"LT xx ON <code>"
"LIGHT xx ON <code>"
"LT xx ON <code>"
9 Turn light xx off
(xx = 01 – 15)
"LIGHT xx ON <code>"
"LT xx ON <code>"
"LIGHT xx ON <code>"
"LT xx ON <code>"
10 Turn PGM on
"PGM ON <code>" "PGM ON <code>"
11 Turn PGM off
"PGM OFF <code>" "PGM OFF <code>"
12 Define custom house identity
(see note)
"HOUSE NAME <code><house
ID>"
"HN <code><house ID>"
"HOUSE NAME <code><house
ID>"
"HN <code><house ID>"
13 Query system status
Not supported command
"STATUS <code>"
"ST <code>"
Note: House ID includes up to 16 characters, for example JOHN'S HOUSE.
Reporting by SMS
The PowerMax Pro system can send SMS messages
to a maximum of 4 pre-selected telephone numbers.
Example of the reported SMS messages:
JOHN’S HOME
**AWAY**
JOHN’S HOME
**DISARM**
JOHN’S HOUSE
POWERMAX: LOW BATTERY
GARAGE: LOW BATTERY
JOHN’S HOUSE
STATUS MESSAGE 01
(Event list is displayed)
Note: Status messages can be sent only to a calling
telephone whose identity number is not blocked by
the user!
Note: The PowerMax Pro may react with a delay to
received SMS messages if a GPRS session is in
progress at the same time.
Conducting a Walk-Test
The walk-test is an indispensable operation by which
you verify that all detectors function properly, without
disturbing the neighbors with loud sirens. The test
must be performed at least once a week, and
should include all detectors in all zones.
Before performing walk-test, all the detectors must
be in normal state. Normal state is achieved when no
motion is made for at least 2 minutes.
Note: During the test period, 24-hour zones will not
cause an alarm if violated, but a fire zone will
function normally.
A typical test will take place as follows:
A. Click
.
The display will read:
WALK TEST
B. Click the button, the display will
prompt you for your user code:
ENTER CODE
_ _ _ _

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Visonic POWERMAXPRO and is the answer not in the manual?

Visonic POWERMAXPRO Specifications

General IconGeneral
BrandVisonic
ModelPOWERMAXPRO
CategorySecurity System
LanguageEnglish

Related product manuals