Wacker Neuson BS 60-2i User Manual (English)

Other manuals for Wacker Neuson BS 60-2i

Questions and Answers:

S
Samantha ByrdSep 3, 2025
What to do if Wacker Neuson Power Tool engine runs but rammer does not tamp?
- F
  fmurraySep 3, 2025
  If the engine of your Wacker Neuson Power Tool is running but the rammer isn't tamping, it could be due to several issues. A damaged clutch may need repair or replacement. Broken connecting rods or crank gears would require replacement of the broken parts. Low engine performance due to compression loss may require adjusting the compression. Also, check for and clear any obstructions in the exhaust port.
M
Melanie KingSep 4, 2025
Why Wacker Neuson Vibratory rammer & tamper engine hard to start?
- M
  Melissa GomezSep 5, 2025
  If your Wacker Neuson vibratory rammer & tamper engine is hard to start, several factors could be the cause. It could be due to dirty air filters, which require cleaning or replacement. Another cause might be too much oil in the fuel, necessitating draining the old fuel and replacing it with a fresh mixture. Fouled or incorrect spark plugs, a dirty muffler or exhaust port, an incorrect fuel mixture adjustment, or low engine compression can also prevent the engine from starting easily. In the case of leaking crankshaft seals or low engine compression, consult the WM 80 Engine Repair Manual or the WM 80, WM 90 or Yanmar Engine Repair Manual respectively.
F
fsextonSep 6, 2025
What to do if Wacker Neuson Vibratory rammer & tamper engine does not start?
- M
  Monica PriceSep 6, 2025
  If your Wacker Neuson vibratory rammer & tamper engine won't start, begin by checking if there's fuel in the tank and ensuring the fuel valve is open. A fouled spark plug could also be the culprit; try cleaning or replacing it and setting the electrode gap. Other potential issues include a plugged fuel filter (replace it and inspect the fuel lines), an incorrect fuel mixture adjustment (adjust the screw and clean the fuel jets), a failed ignition module (replace it), or, on machines with oil injection, a failed float switch (replace it).
D
Dawn GonzalezSep 7, 2025
Why Wacker Neuson Vibratory rammer & tamper engine does not accelerate?
- T
  Tanya HamiltonSep 7, 2025
  If your Wacker Neuson vibratory rammer & tamper engine isn't accelerating properly or is running poorly, consider these potential causes: dirty air filters (clean or replace them), too much oil in the fuel (drain the tank and refill with new mixed fuel), a fouled or incorrect spark plug (clean, replace, and ensure it's a resistor-type), a dirty muffler or exhaust port (clean them), an incorrect fuel mixture adjustment (adjust the screw and clean the fuel jets), or an air leak in the carburetor system (check all connections). For leaking crankshaft seals, consult the WM 80, WM 90, or Yanmar Engine Repair Manual.
W
William LoweSep 8, 2025
Why Wacker Neuson Vibratory rammer & tamper overheats?
- B
  brittany43Sep 8, 2025
  If your Wacker Neuson vibratory rammer & tamper engine is overheating, it could be due to not enough oil in the fuel mix, which requires draining the tank and refilling it with new mixed fuel. Alternatively, the carburetor fuel mix may be set too lean, requiring a reset of the carburetor adjustments. Another potential cause is cooling fins or fan blades packed with dirt, which means you'll need to clean the debris from the fins and blades.
L
ljonesSep 9, 2025
Why Wacker Neuson Vibratory rammer & tamper jumps erratically?
- M
  Mr. Austin Nicholson PhDSep 9, 2025
  If your Wacker Neuson vibratory rammer is jumping erratically, it could be due to oil or grease on the clutch, which requires inspection and cleaning. Another cause might be broken or worn springs in the ramming system, damaged parts in the spring cylinder assembly, or damaged parts in the crankcase assembly; all these issues require disassembling the relevant components, inspecting them, and replacing any damaged parts. Additionally, soil buildup on the ramming shoe or an engine speed that is too low can also cause erratic jumping. Clean the shoe and adjust the engine speed to resolve these issues.