Wacker Neuson WP 1550 User Manual (English)

Questions and Answers:

K
Kyle PachecoAug 2, 2025
Why is my Wacker Neuson WP 1550 Construction Equipment plate not developing full speed and causing poor compaction?
- G
  gmcbrideAug 2, 2025
  There are several potential reasons why your Wacker Neuson plate isn't reaching full speed and compacting poorly. It could be due to the engine throttle control not being fully open or adjusted correctly; in both cases, you should adjust the throttle control. Another reason might be that the ground is too wet, causing the plate to stick, so allow the soil to dry. Other potential causes include a loose or worn drive belt (adjust or replace it), binding exciter bearings (check oil condition and level, adding or changing oil as needed), a clogged air filter (clean or replace it), or low engine speed (check engine speed with a tachometer and adjust or repair the engine).
J
John JohnsAug 11, 2025
What to do if my Wacker Neuson Construction Equipment engine is running but there is no vibration?
- P
  padillacarolynAug 11, 2025
  If your Wacker Neuson construction equipment's engine is running but there's no vibration, the engine throttle may not be open, so open the engine throttle. Alternatively, the drive belt might be loose or broken, in which case you should adjust or replace it. A damaged clutch could also be the cause, requiring inspection and replacement. Low engine speed or too much oil in the exciter can also cause this issue; check the engine speed and adjust the oil to the correct level.
B
blackburnlindaAug 21, 2025
Why does my Wacker Neuson Construction Equipment plate jump or compact unevenly?
- P
  Paula NormanAug 21, 2025
  Your Wacker Neuson construction equipment plate might be jumping or compacting unevenly because the ground surface is too hard or the shockmounts are loose or damaged.

Wacker Neuson WP 1550 Specifications

General

Brand	Wacker Neuson
Model	WP 1550
Category	Construction Equipment
Language	English

Summary

Foreword

CALIFORNIA Proposition 65 Warning

Warning regarding engine exhaust chemicals known to cause cancer or reproductive harm.

Safety Information

Laws Pertaining to Spark Arresters

Discusses legal requirements for spark arresters on engines.

Operating Safety

General safety guidelines and precautions for operating the machine.

Operator Safety with Internal Combustion Engines

Specific safety measures for engines, including fuel and exhaust hazards.

Service Safety

Safety precautions to be followed during machine maintenance and repair.

Label Locations

Illustrates the placement of various safety and operational labels on the machine.

Warning and Informational Labels

Explains the meaning of common pictorial labels used on the machine.

Operating Labels

Details the meaning of operational control labels for starting and running the machine.

Company Identification

Describes the company logo and the machine's identification nameplate.

Technical Data

Engine Data

Provides specifications related to the machine's engine, including power and oil.

Plate Data

Lists operational weight, tank capacity, and exciter specifications for the plate.

Sound and Vibration Specifications

Details sound pressure, sound power, and hand/arm vibration levels.

Machine Dimensions

Provides the physical dimensions of the machine with diagrams.

Operation

Recommended Fuel

Specifies the type of fuel required for the engine and its quality.

Before Starting Checks

Outlines pre-operation checks and safety reading requirements.

Starting the Engine

Step-by-step instructions for starting the machine's engine.

Stopping the Engine

Step-by-step instructions for safely stopping the machine's engine.

Machine Application

Describes the intended uses and limitations of the plate compactor.

Operating the Plate Compactor

Guidance on how to operate the plate compactor for effective compaction.

Wheel Kit Installation and Use

Instructions for attaching and using the optional wheel kit for transport.

Maintenance

Periodic Maintenance Schedule

Provides a schedule for routine engine and machine maintenance tasks.

Cleaning the Plate

Instructions for cleaning the plate after use to maintain performance.

Drive Belt Maintenance

Details procedures for checking, adjusting, and replacing the drive belt.

Exciter Lubrication and Fluid Change

Steps for changing the automatic transmission fluid in the exciter assembly.

Spark Plug Service

Procedures for inspecting, cleaning, and replacing the spark plug.

Engine Oil Level Management

Instructions for draining, checking, and refilling the engine oil.

Air Cleaner Maintenance

Steps for cleaning and replacing the dual-element air cleaner.

Fuel Strainer Cleaning

How to remove and clean the fuel strainer and cup.

Troubleshooting Common Issues

Lists common problems, their causes, and recommended remedies.

Machine Storage Procedures

Guidelines for storing the machine for extended periods (over 30 days).

Lifting and Moving the Machine

Instructions for safely lifting the machine manually or mechanically.

Transporting the Machine

Procedures for safely transporting the machine on a vehicle.

Related product manuals

Wacker Neuson RTx-SC3

180 pages

Wacker Neuson RTLx-SC3

186 pages

Wacker Neuson Dumper 5001

130 pages

Wacker Neuson Dumper 6001