What to do if my wallas SPARTAN Heater shows a system error because of a fuel pump issue?
If your Wallas Heater shows a system error related to the fuel pump, it could be due to a fuel pump output short-circuit. Check the wiring to ensure there are no shorts. Alternatively, the fuel pump might not be connected. In this case, connect the fuel pump connector.
What to do if my wallas SPARTAN shows a system error because the fuel pump is not connected?
If your Wallas Heater displays a system error indicating that the fuel pump is not connected (no current detected on output), it means the fuel pump is missing. You should connect the fuel pump connector.
What to do if my wallas SPARTAN shows a system error due to low voltage?
If your Wallas Heater displays a system error and the cause is low voltage, which prevents starting, the suggested solution is to renew or charge the battery.
What to do if my Wallas Heater is overheating?
If your Wallas Heater is overheating, it may be caused by high air temperature. Check the air vents and warm air hoses for any blockages.
What to do if my Wallas Heater has ignition failure due to preheating issues?
If your Wallas Heater experiences ignition failure because preheating failed and residual fuel burned for too long, try starting it again. If the fault persists, it is recommended to contact service.
What to do if my wallas SPARTAN coolant is overheating?
If your Wallas Heater's coolant temperature is too high, it indicates coolant overheat. This may be because the coolant is not circulating properly. Bleed the air out of the system and check the coolant pump.
What to do if my Wallas Heater shows a system error due to burner temperature?
If your Wallas Heater displays a system error because the burner temperature is missing or too high, it may be due to a power cut during operation. Wait for the unit to cool down and then try to start it again.
What to do if my Wallas Heater shows a system error because the enable input is not asserted?
If your Wallas Heater displays a system error stating that the enable input is not asserted, it means the enable wire is missing. Connect the enable wire or set the main power to ON.
What to do if my Wallas Heater shows a system error because the air temperature sensor is missing?
If your Wallas Heater shows a system error indicating that the air temperature is missing or invalid, you should connect the air temperature sensor.
What to do if my wallas SPARTAN Heater shows low voltage?
If your Wallas Heater indicates low voltage, and the supply voltage is below the minimum required, renew or charge the battery.
Manual provides information on product safety and instructions to reduce risks of accidents and injuries.
Lists all included supplies and available accessories for the heater unit.
Key factors to consider before proceeding with heater installation.
Details on wall mounting and floor mounting methods for securing the heater device.
Guidance on general and product-specific electrical wiring for the heater.
Instructions for routing warm air outlets and inlet ducting for fresh air.
Covers camper/RV installation, lead-throughs, and exhaust hose routing.
Details on fuel connections, tank fittings, filters, and solenoid valves.
Steps for starting the heater, including first-time start-up and error handling.
How to adjust heat output, use Thermo Control, and Pause feature.
Details on Manual mode, Ventilation mode, and Air Boost functionality.
Procedures for shutting down the device and operating via remote applications.
Methods for installing the control panel, surface mount or behind wall.
Overview of control panel functions, starting procedures, and operating modes.
Connecting the heater to a mobile device via the Wallas Remote application.
Instructions and precautions for checking and performing software updates.
Pre-test run checklist to ensure proper installation and component setup.
Guidance on the initial start-up process and running the device for the first time.
Regular service intervals, special recommendations, and winter storage advice.
List of possible error codes, their problems, and troubleshooting steps.
Details on product warranty coverage, duration, and claim procedures.
Statements regarding manufacturer liability for improper use or installation.
To Next Page
General
