wallas 40CC - User Manual

C O N T R O L P A N E L
OPERATION GUIDE
C o t t a g e A i r H e a t e r s 2 6 C C a n d 4 0 C C
IGNITION
TEMPERATURE / POWER SETTING
Combustion indicator
Temperature / Power knob
Power button
Power indicator
Thermostat indicator
Thermostat sensor
Heating indicator
1.
2.
3.
4.
5.
6.
7.
1
2
3
4
5
6
7
SUN SWITCH
(IN PI THERMO MODE)
Orange thermostat light will begin to
flash every 30 seconds.
Sun Switch automatically turns the heater off if the
temperature remains +3 C (37 F) above the set level for
1/2 hour due to temperuature increase in local ambient
conditions.
Rotate the Temperature/Power Knob
slightly to turn the Sun Switch off
temporarily.
If heating is still needed, turn the device
back on manually.
Red combustion light will begin to flash for
about 5 minutes, while the heater is
cooling down.
SHUT DOWN
Press the Power Button down for 2
seconds. Yellow heating light will shut off
immediately.
Heater cannot be restarted until the cool down has
completed. The heating mode that was used last upon
shutdown will be the same mode when the heater is
turned on again.
See
ignition
Please Refer to Manual for Full Operation and Maintenance Instructions at wallas.com
Press the Power Button for 3 seconds
until the yellow power light appears. When
you release the button, the yellow heating
light will appear.
Temperature Chart
for the thermostat
in PI Thermo
Mode:
1: ~ 5 °C (~ 41 °F)
2: ~ 11 °C (~ 52 °F)
3: ~ 17 °C (~ 63 °F)
4: ~ 23 °C (~ 73 °F)
5: ~ 29 °C (~ 84 °F)
6: ~ 35 °C (~ 95 °F)
Red combustion light will light up when
the burner flame has been ignited and the
combustion has stabilised (approx. in 5
min). Heater will be fully operational
approx. 10 min later.
PI Thermo Mode: Set a target temperature (C°/F°)
Manual Mode: Control heating power with knob
Rotate the Temperature/Power Knob to the
desired temperature (refer to temperature
chart on the right) in the PI Thermo Mode or
control heating power with knob in Manual
Mode.
Switch between modes by turning the
Temperature/Power Knob back and forth
to min - max - min quickly.
When the PI Thermo Mode is chosen,
the orange thermostat light is on.
In Manual Mode, the light is off.
All rights reserved. Wallas-Marin reserves the right to change or improve its products and to make changes in the content of this guide
without obligation to notify any person or organization of such changes or improvements. Go to www.wallas.com for current updates
and supplemental information concerning the use of this product.

Summary

Ignition Process

Temperature and Power Settings

PI Thermo Mode Operation

Set a target temperature (C°/F°) for the heater in PI Thermo Mode.

Manual Mode Operation

Control heating power directly with the knob in Manual Mode.

Mode Switching

Switch between PI Thermo and Manual modes by cycling the knob.

Sun Switch Functionality

Shutdown Procedure

Items to Note and Safety

Cooldown Process Warning

Do not turn off power during the cooldown process after shutdown.

Generator;Charger Start Warning

Avoid starting the unit while charging to prevent over-voltage.

First Ignition and Lockout

Initial Start-up

First ignition may require multiple attempts if fuel line is empty.

Lockdown Procedure

Unit locks after two unsuccessful start attempts; requires unlock.

Unlocking the Unit

Indicator Light Status

Normal Operation Lights

Explanation of lights indicating heating, combustion, and cooldown.

Fault and Error Indicators

Description of lights indicating low voltage, overheat, or faults.

Specific Fault Codes

Interpreting light patterns for glow failure or blower faults.

Remote Control Accessory

wallas 40CC Specifications

General

Brand	wallas
Model	40CC
Category	Heater
Language	English