Waring WFP11S - Assembly of Batch Bowl Parts; Assembling with the S-Blade; Assembling with Accessory Discs

7
ASSEMBLY of BATCH BOWL PARTS
WFP11S & WFP14S
We will use the terms work bowl, batch bowl and cutter bowl interchangeably throughout this
instruction book. They mean the same thing.
r$MFBOBOETBOJUJ[FUIFNPUPSCBTFBOEXBTISJOTFBOETBOJUJ[FUIFCPXMDPWFSGPPEQVTIFSGPPE
pusher insert and processing tools prior to initial use.
r1MBDFUIFCBTFPOBDPVOUFSPSUBCMFOFBSBQSPOHFMFDUSJDBMPVUMFU1PTJUJPOJUTPZPVMPPLBUUIF
front of the unit and can see the control levers. Be certain that the cord is unplugged and the OFF
lever has been pressed. Do not plug in the cord until the processor is completely assembled.
r1JDLVQUIFUSBOTQBSFOUXPSLCPXMIPMEJOHJUJOCPUIIBOETXJUIUIFIBOEMFUPXBSEZPV
r1MBDFUIFCPXMPOUIFCBTFGJUUJOHJUTDFOUSBMUVCFPWFSUIFNPUPSTIBGUPOUIFCBTFBOEQMBDJOHJUT
handle slightly to the left of front-center (at about a 7 o’clock position).
r1SFTTUIFCPXMEPXOTPUIFMPXFSSJNGJUTBSPVOEUIFDJSDVMBSQMBUGPSN5VSOUIFCPXMDPVOUFSDMPDL-
wise as far as it will go. It will lock into position with the tabs on the sides of the platform.
Read this if assembling the batch bowl parts to use S-blade (cutter blade).
r1JDLVQUIFNFUBMCMBEFOPUJOHUIFEJBHSBNPOUIFUPQPGUIFQMBTUJDDFOUFS*UNBUDIFTUIFTIBQFPG
the motor shaft.
r1MBDFUIF4CMBEFPWFSUIFUJQPGUIFNPUPSTIBGUMJOJOHVQUIFJOTJEFPGUIFIVCXJUIUIFTIBGU
Press it down firmly, rotating the center hub until the blade assembly is fully seated. It should
easily drop into place. Push firmly to lock and seal S-blade hub in place. Be sure it is pushed down as
far as it will go. If it is not all the way down, it may become damaged and any liquid may leak. Push
only on the center section (plastic part); never touch the cutting blade as it is extremely sharp.
r$IFDLUPCFTVSFUIFCMBEFJTBMMUIFXBZEPXOCZUVSOJOHJUCBDLBOEGPSUIXIJMFMJHIUMZQVTIJOHJU
down. If properly installed and fully seated, the lower blade will be positioned just above the inside
bottom of the bowl.
r*GQSPDFTTJOHGPPEXJUIUIF4#MBEFOPXJTUIFUJNFUPBEEUIFGPPEPSMJRVJEUPUIFXPSLCPXM
r"MXBZTQSPDFTTESZGPPEGJSTUUIFOBEEXFUGPPE
r%POPUGJMMMJRVJEPWFSi.BYMJRVJEGJMMuMJOF*GUPPNVDIMJRVJEJTVTFEJUXJMM
overflow. In this case, stop operation, remove liquid to below “Max liquid fill”
line and continue processing.
Read this if assembling batch bowl parts to use accessory discs in batch bowl.
r%POPUQVUBOZGPPEJOUIFCPXMCFGPSFQMBDJOHUIFBDDFTTPSZEJTDPOUPUIFTIBGU
r4FMFDUUIFBQQSPQSJBUFBDDFTTPSZEJTDHSBUJOHEJTDTISFEEJOHEJTDPSTMJDJOHEJTD
r)PMEUIFEJTDXJUIUIFDVUUJOHTJEFGBDJOHZPVSIBOE#FDBSFGVMOPUUPTDSBQFZPVS
hand on the sharp edges. Notice the bottom of the disc has a plastic receptacle for
the detachable stem. Holding the stem with your thumb on the release switch, place the center and
right-most two tabs in the two open slots on the bottom of the disc and rotate clockwise. Refer to
diagram.
r0ODFUIFTUFNJTJOTUBMMFEJOUIFQSPQFSEJTDDBSFGVMMZHVJEFUIFDFOUFSEJTDIVCPWFSUIFNFUBMTIBGU
so the double flats on the shaft line up with the disc stem. Put the disc on top of the shaft and rotate
until it drops down and into place. Be sure it is pushed down as far as it will go. Push on the outside
rim only; never touch the cutting blades. It should easily drop into place, but if not, then gently rock
it back and forth until you feel the disc drop into place.
(batch bowl assembly continued)
L
O
C
K
U
N
L
O
C
K
w ww . . co m
information@itm.com1.800.561.8187