Warn 103950 - User Manual

Quick Start Guide
UNIVERSAL WARN® HUB Receiver
MOUNT
KIT CONTENTS BEFORE YOU BEGIN
1.
WARN HUB
Download the WARN® HUB App (HUB
App) from the App Store or Google Play.
Data rates may apply.
Apple is a trademark of Apple Inc., registered in the U.S. and in other countries. App Store is
a service mark of Apple Inc.
Google Play is a trademark of Google Inc.
2.
3.
Determine mounting location and wire routing path.
Recommendation: Under vehicle hood, on vehicle frame
or along other wiring bundles. Avoid sharp edges, heat
and moving parts.
Using the included zip-ties, mount HUB Receiver rmly
to vehicle.
Route spade terminal ends of the HUB Receiver to the
winch control pack/contactor. NOTE: Make sure to route
wires/cables away from sharp edges, heat and moving
parts.
4.
• Disconnect vehicle power.
• Connect the HUB Receiver’s
spade terminal wires to the
contactor’s spade connectors*.
• Connect HUB Receiver’s red
wire to key-on ignition wire.
• Connect black wire to vehicle
ground.
• Reconnect vehicle power.
* Illustration depicts wiring a powersports
contactor. For winches with a control pack,
the spade terminal colors may differ. See
owner’s manual for details.
White
Brown
Green
Red
Black
(ground)
Quick Start Guide
UNIVERSAL WARN® HUB Receiver
WIRE
PAIR/CONNECT
CUSTOMER SERVICE
WARN INDUSTRIES, INC. 12900 S.E. Capps Road,
Clackamas, OR USA 97015-8903, 1-503-722-1200
Customer Service: 1-800-543-9276
Dealer Locator Service: 1-800-910-1122
POWER
5.
6.
7. 8. 9.
WARNING
All work with electrical wires and cables must be completed with the battery completely
disconnected from the vehicle wiring.
Turn vehicle power on.
NOTE: The HUB Receiver is active
when the yellow light is on.
I
II
III
0
Continue
You are now connected!
Press and hold button on HUB
Receiver until blue light ashes
(approximately 2 seconds) and then
release button.
Open app on phone and follow
prompts.
I agree to the latest
Privacy Policy,
Terms of Use and
Safety Agreement
x
Continue
When light on HUB Receiver turns
green, you are connected.
Continue following the instructions
through your app.
103972A0

Summary

Before You Begin

Download the WARN HUB App

Download the WARN® HUB App from the App Store or Google Play.

Mounting Instructions

Determine Mounting Location

Determine mounting location and wire routing path, avoiding hazards.

Mount HUB Receiver

Mount HUB Receiver firmly to vehicle using included zip-ties.

Route Wiring

Route spade terminal ends to winch control pack, away from hazards.

Wiring Connections

Connect HUB Receiver Wiring

Wire HUB Receiver by connecting spade terminals, red wire to ignition, and black wire to ground.

Powering On

Turn On Vehicle Power

Turn vehicle power on. The HUB Receiver is active when the yellow light is on.

Pairing and Connection

Initiate Pairing

Press and hold HUB Receiver button until blue light flashes, then release.

Open App and Follow Prompts

Open the app on your phone and follow the on-screen prompts.

Confirm Connection

Connection is successful when the HUB Receiver light turns green. Follow app instructions.

Warn 103950 Specifications

General

Part Number	103950
Product Type	Winch
Motor	12V DC, Series Wound
Gear Train	3-Stage Planetary
Gear Ratio	218:1
Rope	Steel
Fairlead	Roller
Recommended Battery	650 CCA Minimum
Remote Control	Yes
Brake	Mechanical Cone
Rope Length	80 ft (24.38 m)
Battery Leads	2 Gauge
Finish	Powder Coated
Rated Line Pull	10, 000 lbs (4536 kg)