5
Need help or have any questions? Call us at 1-714-963-0329 or send us an Email at service@globalhobby.net
❑ Kwik Bond 5 Minute Epoxy # 887560
❑ Kwik Bond Thick C/A # 887510
❑ Pacer Z-42 Threadlocker # 339162
❑ # 0 & # 1 Phillips Head Screwdrivers
❑ 1.5mm Hex Wrench
❑ Magnum Z-Bend Pliers # 237473
❑ Wire Cutters
❑ Needle Nose Pliers
❑ Adjustable Wrench
❑ Excel Modeling Knife # 692801
❑ Scissors
❑ Ruler
❑ Pencil
❑ Masking Tape
❑ Builder's Triangle
❑ 220 Grit Sandpaper w/Sanding Block
❑ Paper Towels
❑ Rubbing Alcohol
❑ NHP Epoxy Mixing Sticks # 864204
❑ NHP Epoxy Mixing Cups # 864205
❑ K&S 30 Watt Soldering Iron # 598120
❑ Solder
FOR MOTOR BREAK IN YOU WILL NEED:
❑ Emerald Performance Plus Motor Spray # 340186
❑ Trinity Motor Break-In Drops # 840768
❑ Rubber Bands
Here's a List of What We Used to Finish Our Hyper Wing 400 EP:
✦✦
✦✦
✦
IMPORTANT
✦✦
✦✦
✦
The part number listed for the Cirrus servos is compatible with all radio control systems. This servo uses a
universal connector. The part number listed for the Cirrus MRX-4 receiver is compatible with Hitec and Futaba radio control
systems. This receiver is also available for JR and Airtronics radio control systems. The Wattage IC-15A Micro ESC is compatible
with Futaba, JR, Hitec, Airtronics-Z and others.
When you purchase the Cirrus MRX-4 receiver, you must also purchase a Hitec brand crystal compatible with the receiver. The
crystal must also be on the same frequency as your transmitter. Note that the MRX-4 receiver uses a single conversion FM
Hitec crystal.
QTY. 1 443526 Cirrus MRX-4 Micro Receiver (Neg. Shift, Hitec/Futaba)
Hitec Single Conversion FM RX Crystal
QTY. 2 444035 Cirrus CS-6.2 Micro Servos
QTY. 1 128484 Wattage IC-15A Micro Electronic Speed Control
QTY. 1 128538 Wattage 8 Cell 800Mah 5/4AAA NiMH Flight Battery
QTY. 1 130108 Wattage PF-12 AC/DC Park Flyer Charger
3M 3/4" Wide Clear Plastic Tape - Available at Most Hardware Stores
INFORMATION ABOUT COVERING YOUR HYPER WING 400 EP
Your Wattage Hyper Wing 400 EP comes with four self-adhesive decal "skins" that can be used to cover the entire surface of the top
and bottom of your airplane. By using this decal material, the weight of the Hyper Wing 400 EP is kept to a minimum while adding
strength to the structure and making the airplane look good. If you want you can choose to leave your Hyper Wing 400 EP
uncovered, cover it in after-market colored packing tape or cover it using your favorite materials and methods. Keep in mind,
though, that the idea is too keep the airplane as light as possible, yet still be strong and look good.
Included is white plastic reinforcement tape that can be attached to the underside of the leading edge to help prevent damage during
landing. To help save weight, this should only be applied if you will be landing on rough surfaces or if you are using heavier
than recommended flight gear.
Note: The Hyper Wing 400 EP uses
elevons for control. If your radio
transmitter does not have elevon mixing
capability, you will need to purchase an
electronic elevon mixer. We suggest the
Wattage Elevon Mixer P/N 128460.
OUR RECOMMENDATIONS, CONTINUED....
SECTION 2: TOOLS AND SUPPLIES REQUIRED
To Next Page
Loading...
