Wayne SPF33 - User Manual

SPECIFICATIONS
POWER SUPPLY REQUIREMENTS 120 V, 60 Hz
MOTOR Single Phase, Dielectric Oil Filled
HORSEPOWER 1 HP .................... (CDU1000)
3/4 HP ................ (CDU980E)
1/2 HP............ (CICDU800, CDU800,
............................. SPF50, CDT50)
1/3 HP ........... (CICDU790, CDU790,
................................SPF33, WST33)
CIRCUIT REQUIREMENTS 15 A (minimum)
DIMENSIONS 11-1/2 in. high x 9-3/4 in. base
ON LEVEL (FACTORY SET) Vertical: Approximately 9 in.
Tether: Approximately 13 in.
OFF LEVEL (FACTORY SET) Vertical: Approximately 4 in.
Tether: Approximately 7 in.
600002-001 D 05/19
© 2018, WAYNE/Scott Fetzer Company
Submersible Sump Pump
www.waynepumps.com
Intended for Indoor Use Only
Vertical Float Switch
Tether Float Switch
Please read and save these instructions. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property
damage! Retain instructions for future reference.
Operating Instructions and Parts Manual Sumps
*Images are for illustration purposes only.
Not all models are shown.
CONSTRUCTION
MOTOR HOUSING
Cast Iron (CICDU800, CICDU790), Stainless Steel,
(CDU1000, CDU980E) Coated Steel ( CDU800,
CDU790, SPF33, SPF50, CDT50) Reinforced
Thermoplastic (WST33)
VOLUTE
CDU1000, CDU980E,
CDU800, CDU790, CDT50
Cast Iron
SPF33, SPF50, WST33
Glass Reinforced Thermoplastic
IMPELLER Glass Reinforced Thermoplastic
SHAFT Steel
DISCHARGE 1-1/2 in. NPT
PERFORMANCE GAL/HR
Model HP
Discharge Head (Lift Distance)
0 ft 5 ft 10 ft 15 ft 20 ft
CDU1000 1/2 6100 5460 5100 4560 3840
CDU980E 3/4 5490 5076 4600 4100 3500
CICDU800,
CDU800, CDT50
1/2 5100 4500 3840 3060 2040
CICDU790,
CDU790
1/3 4600 3810 3060 2220 1200
SPF50 1/2 4300 3900 3360 2700 1260
SPF33 1/3 3750 3300 2718 1920 -
WST33 1/3 3000 2610 2130 1404 400

Wayne SPF33 Specifications

General

Model	SPF33
Horsepower	1/3 HP
Voltage	115 V
Construction	Thermoplastic
Type	Submersible
Discharge Size	1-1/2" NPT
Inlet/Outlet Size	1-1/2" NPT

Summary

SPECIFICATIONS

PERFORMANCE GAL;HR

Performance Data by Model and Head

SAFETY SIGNAL WORDS & WARNINGS

General Safety Precautions

Highlights critical safety terms like DANGER, WARNING, CAUTION, and NOTICE.

Electrical Safety Guidelines

Covers grounding, GFCI protection, cord handling, and circuit breaker requirements.

Hazard Warnings

Addresses specific risks like electric shock and wet floor hazards during operation or maintenance.

ADDITIONAL SAFETY WARNINGS

Fluid and Environment Restrictions

Prohibits pumping flammable, explosive, or non-potable water; warns against specific atmospheres.

Installation and Handling Precautions

Advises on installer responsibility, piping, check valves, damage, and proper lifting methods.

OPERATIONAL AND MAINTENANCE ADVICE

Pump Usage Restrictions

Tether Switch Replacement

TYPICAL SUMP INSTALLATION STEPS

Basin Preparation and Base Setup

Pump Placement and Switch Operation

Plumbing and Electrical Connections

Post-Installation Testing and Checks

TROUBLESHOOTING WARNINGS

Service and Maintenance Safety

Emphasizes disconnecting power and allowing the pump to cool before servicing.

TROUBLESHOOTING GUIDE

Pump Fails to Start or Run

Lists common causes like low water, blown fuse, voltage, motor, switch, or clogs.

Intermittent Pumping Issues

Thermal Overload Protection

TROUBLESHOOTING GUIDE (Continued)

GFCI Tripping or Pump Noise

Covers GFCI issues and causes of excessive noise or vibration.

Pump Not Shutting Off or Low Output

Details reasons for the pump failing to shut off or delivering reduced water volume.

ROUTINE SUMP MAINTENANCE

Regular Inspection and Cleaning

Operational Tests and Replacements

CUSTOMER SUPPORT AND WARRANTY INFORMATION

Limited Warranty Coverage

Warranty Exclusions and Limitations