Why my Weber mt CR 7 Power Tool soil compactor does not start?
If your soil compactor isn't starting, there could be several reasons: * You might not be starting it correctly, so review the starting procedure. * The fuel level might be low, so check the fuel level. * A dirty fuel filter can prevent starting, so replace the fuel filter. * Also, a dirty air filter can cause issues, so clean or replace the air filter cartridge.
What to do if my Weber mt Power Tool has no vibration or insufficient forward travel?
If your Power Tool is experiencing no vibration or insufficient forward travel, the vibrator V-belt might be defective. The suggested solution is to replace the vibrator V-belt.
General| Brand | Weber mt |
|---|---|
| Model | CR 7 |
| Category | Power Tool |
| Language | English |
Describes the machine as a hand-guided, reversible soil compactor, its sections, engine, and controls.
Emphasizes reading and complying with all safety instructions to avoid hazards and property damage.
Details the machine's intended purpose for specific soil types and proper operating conditions.
Lists activities the machine is not suitable for and associated risks.
Highlights the risk of accidents in the immediate danger area and the need to inform others.
Specifies age, training, and compliance with regulations for machine operators.
Lists essential PPE required for operation and maintenance.
Defines the immediate danger area around the machine and its restriction.
Prohibits unauthorized modifications and stresses the use of original spare parts.
Details essential checks and safety precautions before starting the machine.
Provides critical safety instructions for starting the engine and avoiding damage.
Instructions for monitoring surroundings, shutting down for damage, and understanding indicator lights.
Ensures safe parking on level surfaces and securing parked machines.
Details safe fueling practices to prevent fire and environmental damage.
Guidelines for safe cleaning procedures and handling of residual fluids.
Warns about hazardous exhaust emissions like carbon monoxide.
Specifies the need for expert inspection at least annually and record-keeping.
Explains the meaning of various safety signal words and symbols.
Illustrates and explains the meaning of various safety stickers found on the machine.
Steps to take before the first use: check for damage, completeness, and fluid levels.
Identifies and labels key components of the CR 7 machine in a diagram.
Explains indicator lights and key switch functions for the MS 15 start module.
Details indicators and operating hours counter for MS 25/35 start modules.
Explains the operation of the key switch for ignition and starting the engine, including safety notices.
Indicates when the compaction control system is operational and proper frequency is reached.
Shows the achieved level of soil compaction using LEDs.
Warns of operating on soils that are too hard for the machine.
Details the meaning of indicator lights during function tests, start-up, and operation.
Lists visual inspections and other checks to perform before starting work to prevent failures.
Step-by-step guide for starting the engine, including safety warnings and procedures.
Instructions for compacting, including safety precautions for proximity to walls and soil conditions.
Procedure for safely switching off the engine and securing the machine.
Guidelines for safely lifting the machine onto a vehicle using appropriate gear.
Instructions for securing the machine against theft and unauthorized use when stored on-site.
Measures for cleaning, checking fluids, and battery maintenance for long-term storage.
Emphasizes reading instructions for regular maintenance to prevent downtimes and avoid risks.
Specifies that maintenance and repairs require qualified and trained professionals.
Highlights risks during maintenance, protective fixture refitting, fluid disposal, and engine safety.
Provides a table outlining maintenance activities and their required frequency.
Step-by-step instructions for cleaning or replacing the air filter insert and cover.
Procedure for inspecting the V-belt for cracks and wear and replacing it if necessary.
Instructions for checking the engine oil level using the dipstick and topping up if needed.
Detailed steps for draining old engine oil and refilling with fresh oil.
Procedure for draining oil, removing, cleaning, and reinstalling the engine oil filter.
Instructions for draining water from the fuel water separator to prevent environmental pollution.
Steps for draining the fuel tank and replacing the fuel filter.
Procedure for checking the hydraulic oil level using the view glass.
Steps for draining and refilling the oil in the exciter unit.
Procedure for accessing and replacing defective fuses.
Instructions for connecting and using a permanent charger for the battery.
Details the types and quantities of operating materials required for the engine, fuel tank, vibrator, and gearshift.
To Next Page
