WEG CFW300 V1.3X - Page 2

WEG CFW300 V1.3X

157 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Default Chapter5
- Table of Contents5
Quick Reference of Parameters, Alarms and Faults9
1 Safety Instructions27
- Safety Warnings in this Manual27
- Safety Warnings in the Product27
- Preliminary Recommendations27
2 General Information29
- About the Manual29
- Terminology and Definitions29
  - Terms and Definitions Used29
  - Numerical Representation30
3 About the Cfw30031
4 Hmi and Basic Programming35
- Use of the Hmi to Operate the Inverter35
- Indications on the Hmi Display35
- Operating Modes of the Hmi35
5 Programming Basic Instructions37
- Access and Indications of Hmi37
- Backup Parameters40
- Situations for Config Status41
- Engineering Units for Softplc42
6 Identification of the Inverter Model and Accessories43
- Inverter Data43
7 Logical Command and Frequency Reference47
- Selection for Logical Command and Frequency Reference47
- Frequency Reference52
- Control Word and Inverter Status57
  - Control Via HMI Inputs59
  - Control Via Digital Inputs59
8 Available Motor Control Types61
9 Scalar Control63
- PARAMETERIZATION of the V/F SCALAR CONTROL65
- START-UP in V/F MODE69
- Energy Saving69
5 V W Vector Control73
- Vvw Vector Control Parameterization75
- Start-Up in V V W Mode78
11 Functions Common to All the Control Modes81
- Ramps81
- DC Link Voltage and Output Current Limitation83
- Flying Start / Ride-Through87
  - Flying Start Function87
  - Ride-Through Function88
- DC Braking88
- Skip Frequency90
- Fire Mode91
12 Digital and Analog Inputs and Outputs93
- Analog Inputs93
- Ntc Sensor Input97
- Analog Output98
- Frequency Input101
- Digital Inputs103
- Input for Infrared Receiver112
- Digital Outputs112
13 Dynamic Braking117
14 Faults and Alarms119
- Motor Overload Protection (F072 and A046)119
- Igbts Overload Protection (F051 and A050)121
- Motor Overtemperature Protection (F078)121
- Overcurrent Protection (F070)122
- Link Voltage Supervision (F021 and F022)122
- W Control Mode Self-Tuning Fault (F033)122
- Remote Hmi Communication Fault Alarm (A700)122
- Remote Hmi Communication Error Fault (F701)123
- Auto-Diagnosis Fault (F084)123
- Fault in the Cpu (F080)123
- Save User Function Fault (F081)123
- Copy Function Fault (F082)123
- External Alarm (A090)123
- External Fault (F091)123
- Fault History124
- Fault Control125
15 Reading Parameters127
16 Communication133
- SERIAL USB, BLUETOOTH, RS-232 and RS-485 INTERFACE133
- Can - Canopen / Devicenet Interface134
- Profibus Dp Interface135
- Commands and Communication Status136
17 Softplc137
18 Applications139
- Introduction139
- Pid Controller139

Related product manuals

Preview: WEG CFW300

Preview: WEG CFW09

Preview: WEG CFW-11

Preview: WEG CFW700

Preview: WEG CFW500

Preview: WEG CFW900

Preview: WEG CFW100

Preview: WEG CFW-10

Preview: WEG CFW500 V1.8X

WEG CFW500 V1.8X

Preview: WEG CFW-11 Series

WEG CFW-11 Series

Preview: WEG DeviceNet CFW500

WEG DeviceNet CFW500

Preview: WEG CFW-10 EASYDRIVE

WEG CFW-10 EASYDRIVE

WEG CFW300 V1.3X - Page 2