WEG CFW300 V1.3X User Manual

157 pages

To Next Page

Motors I Automation I Energy I Transmission & Distribution I Coatings

Frequency Inverter

CFW300 V1.3X

Programming Manual

Default Chapter5
- Table of Contents5
Quick Reference of Parameters, Alarms and Faults9
1 Safety Instructions27
- Safety Warnings in this Manual27
- Safety Warnings in the Product27
- Preliminary Recommendations27
2 General Information29
- About the Manual29
- Terminology and Definitions29
  - Terms and Definitions Used29
  - Numerical Representation30
3 About the Cfw30031
4 Hmi and Basic Programming35
- Use of the Hmi to Operate the Inverter35
- Indications on the Hmi Display35
- Operating Modes of the Hmi35
5 Programming Basic Instructions37
- Access and Indications of Hmi37
- Backup Parameters40
- Situations for Config Status41
- Engineering Units for Softplc42
6 Identification of the Inverter Model and Accessories43
- Inverter Data43
7 Logical Command and Frequency Reference47
- Selection for Logical Command and Frequency Reference47
- Frequency Reference52
- Control Word and Inverter Status57
  - Control Via HMI Inputs59
  - Control Via Digital Inputs59
8 Available Motor Control Types61
9 Scalar Control63
- PARAMETERIZATION of the V/F SCALAR CONTROL65
- START-UP in V/F MODE69
- Energy Saving69
5 V W Vector Control73
- Vvw Vector Control Parameterization75
- Start-Up in V V W Mode78
11 Functions Common to All the Control Modes81
- Ramps81
- DC Link Voltage and Output Current Limitation83
- Flying Start / Ride-Through87
  - Flying Start Function87
  - Ride-Through Function88
- DC Braking88
- Skip Frequency90
- Fire Mode91
12 Digital and Analog Inputs and Outputs93
- Analog Inputs93
- Ntc Sensor Input97
- Analog Output98
- Frequency Input101
- Digital Inputs103
- Input for Infrared Receiver112
- Digital Outputs112
13 Dynamic Braking117
14 Faults and Alarms119
- Motor Overload Protection (F072 and A046)119
- Igbts Overload Protection (F051 and A050)121
- Motor Overtemperature Protection (F078)121
- Overcurrent Protection (F070)122
- Link Voltage Supervision (F021 and F022)122
- W Control Mode Self-Tuning Fault (F033)122
- Remote Hmi Communication Fault Alarm (A700)122
- Remote Hmi Communication Error Fault (F701)123
- Auto-Diagnosis Fault (F084)123
- Fault in the Cpu (F080)123
- Save User Function Fault (F081)123
- Copy Function Fault (F082)123
- External Alarm (A090)123
- External Fault (F091)123
- Fault History124
- Fault Control125
15 Reading Parameters127
16 Communication133
- SERIAL USB, BLUETOOTH, RS-232 and RS-485 INTERFACE133
- Can - Canopen / Devicenet Interface134
- Profibus Dp Interface135
- Commands and Communication Status136
17 Softplc137
18 Applications139
- Introduction139
- Pid Controller139

Questions and Answers:

Need help?

Do you have a question about the WEG CFW300 V1.3X and is the answer not in the manual?

WEG CFW300 V1.3X Specifications

General

Protection Degree	IP20
Input Voltage	200-240 V
Protection Features	Overcurrent, overvoltage, undervoltage, short circuit
Communication	Yes
Communication Interface	RS-485
Operating Temperature	-10°C to 50°C
Humidity	5-95% (non-condensing)
Dimensions	Varies by model
Weight	Varies by model
Control Mode	Scalar (V/f), Sensorless Vector (SVC)
Storage Temperature	-20°C to 60°C