How to solve WEG CFW11M G2 inverter disabled error?
The Inverter Disabled (A702) error on WEG DC Drives happens when the SoftPLC Run/Stop command is equal to Run or a movement block has been enable while the inverter is general disabled. Check and adjust movement block settings.
What to do if WEG DC Drives show motor overload?
If your WEG DC Drives display a motor overload (F072), it means the load on the motor shaft is too high. You should reduce the load on the motor.
What to do if WEG CFW11M G2 show IGBTs overload fault?
If WEG DC Drives show an IGBTs Overload Fault (F048), it means the inverter output current is too high. Reduce the inverter output current.
How to fix WEG CFW11M G2 DC Drives output overcurrent fault?
The F071 fault on WEG DC Drives, which indicates an output overcurrent, is often due to load inertia being too high or the acceleration ramp being too fast. Decrease load inertia or adjust ramp settings to resolve this.
What causes WEG DC Drives to show DC link overvoltage?
A DC Link Overvoltage (F022) on WEG DC Drives is caused by a supply voltage that is too high, resulting in voltage on the DC link exceeding the maximum value. Ensure that the supply voltage is within specified limits.
How to resolve WEG CFW11M G2 DC Drives 24Vdc power supply undervoltage?
A 24Vdc Power Supply Undervoltage (F020) on WEG DC Drives occurs when the voltage on the power supply is below 22.8 Vdc. Check the power supply voltage.
What causes WEG DC Drives to lose communication?
Communication Lost (A088) on WEG DC Drives is often due to a loose keypad cable connection. Secure loose connections of the keypad.
What to do if WEG DC Drives encoder/motor wiring is inverted?
If WEG DC Drives report that the encoder/motor wiring is inverted (F067), the U, V, W wiring to the motor is inverted. Correct the wiring of the motor and encoder.
What causes WEG CFW11M G2 DC Drives to show high load on the motor?
If WEG DC Drives show a High Load on the Motor (A046), it means the load is too high for the used motor. Adjust load or select proper motor settings.
What to do if WEG CFW11M G2 show DC link undervoltage?
If WEG DC Drives display a DC Link Undervoltage (F021), the supply voltage is likely too low, causing the voltage on the DC link to fall below the minimum value. Verify supply voltage setting in parameter P0004.
Explains the meaning of warning symbols used in the manual.
Describes symbols attached to the product for safety warnings.
Outlines essential precautions for installation and operation.
Explains the scope and purpose of the user manual.
Defines key terms and acronyms used throughout the document.
Provides an overview of the CFW-11M G2 inverter and its features.
Covers environmental conditions, component list, lifting, and panel mounting.
Details rectifier, busbars, fuses, wiring diagrams, and connections.
Explains the installation and operation of the safety stop feature.
Describes the functions of the inverter's integral keypad and its keys.
Details the organization and navigation of inverter parameters.
Lists pre-start-up checks and configurations required before powering on.
Guides through the initial inverter start-up process and parameter settings.
Explains inverter behavior and reset procedures when a fault occurs.
Lists common faults, alarms, and their potential causes.
Provides corrective actions for common operational issues.
Refers to the safety stop function and related accessories.
Lists available accessories and their installation notes.
Details electrical specifications related to power supply and input.
Covers control methods, output frequency, performance, and I/O.
Provides physical dimensions and mass of the inverter modules.
General| Category | DC Drives |
|---|---|
| Series | CFW11M G2 |
| Enclosure Rating | IP20 |
| Communication Interface | RS485 (Modbus RTU) |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short circuit |
| Operating Temperature | -10°C to 50°C |
| Humidity | Up to 95% non-condensing |
| Storage Temperature | -25°C to 65°C (-13°F to 149°F) |
To Next Page
