How to fix WEG CFW11M G2 encoder signal fault?
An Encoder Signal Fault (F079) in WEG DC Drives is caused by broken wiring between the motor encoder and option kit for encoder interface. Replace or repair broken wiring of the encoder.
How to resolve WEG DC Drives power module W fault?
A Power Module W Fault (F038) on WEG DC Drives indicates a short circuit between phases W and U or W and V of the motor. Inspect the motor for short circuits.
How to resolve WEG CFW11M G2 power module V fault?
A Power Module V Fault (F034) on WEG DC Drives indicates a short circuit between phases V and U or V and W of the motor. Inspect the motor for short circuits.
Why WEG CFW11M G2 DC Drives show overcurrent/short circuit error?
The F070 error on WEG DC Drives indicates an overcurrent or short circuit, likely caused by a short circuit between two motor phases. To resolve this, inspect the motor for shorts.
What causes WEG CFW11M G2 DC Drives to show high load on the motor?
If WEG DC Drives show a High Load on the Motor (A046), it means the load is too high for the used motor. Adjust load or select proper motor settings.
How to fix WEG CFW11M G2 motor current imbalance?
A Motor Current Imbalance (F076) in WEG DC Drives is due to a loose connection or broken wiring between the motor and inverter connection. Fix any broken or loose connections.
What to do if WEG CFW11M G2 show DC link undervoltage?
If WEG DC Drives display a DC Link Undervoltage (F021), the supply voltage is likely too low, causing the voltage on the DC link to fall below the minimum value. Verify supply voltage setting in parameter P0004.
What causes high motor temperature on WEG DC Drives?
High Motor Temperature (A110) in WEG DC Drives is caused by excessive load at the motor shaft. Reduce the load on the motor.
How to fix motor overtemperature on WEG DC Drives?
If WEG DC Drives report a motor overtemperature (F078), it's because the load on the motor shaft is too high. You should reduce the load or enhance cooling.
Why WEG CFW11M G2 DC Drives show IGBTs overload alarm?
The IGBTs Overload Alarm (A047) on WEG DC Drives indicates that the inverter output current is too high. Reduce the inverter output current.
General| Category | DC Drives |
|---|---|
| Series | CFW11M G2 |
| Enclosure Rating | IP20 |
| Communication Interface | RS485 (Modbus RTU) |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short circuit |
| Operating Temperature | -10°C to 50°C |
| Humidity | Up to 95% non-condensing |
| Storage Temperature | -25°C to 65°C (-13°F to 149°F) |
Explains the meaning of warning symbols used in the manual.
Describes symbols attached to the product for safety warnings.
Outlines essential precautions for installation and operation.
Explains the scope and purpose of the user manual.
Defines key terms and acronyms used throughout the document.
Provides an overview of the CFW-11M G2 inverter and its features.
Covers environmental conditions, component list, lifting, and panel mounting.
Details rectifier, busbars, fuses, wiring diagrams, and connections.
Explains the installation and operation of the safety stop feature.
Describes the functions of the inverter's integral keypad and its keys.
Details the organization and navigation of inverter parameters.
Lists pre-start-up checks and configurations required before powering on.
Guides through the initial inverter start-up process and parameter settings.
Explains inverter behavior and reset procedures when a fault occurs.
Lists common faults, alarms, and their potential causes.
Provides corrective actions for common operational issues.
Refers to the safety stop function and related accessories.
Lists available accessories and their installation notes.
Details electrical specifications related to power supply and input.
Covers control methods, output frequency, performance, and I/O.
Provides physical dimensions and mass of the inverter modules.
To Next Page
