What causes A128 Timeout for Serial Communication in WEG DC Drives?
A Timeout for Serial Communication (A128) in WEG DC Drives suggests you check the wiring and grounding installation. Ensure proper wiring and grounding for communication.
Why does my WEG Inverter display an F048 IGBT Overload Fault?
The WEG Inverter indicates an IGBT overload fault because the inverter output current is too high.
What does the F070 Overcurrent/Short-circuit fault mean on my WEG Inverter?
The WEG Inverter has detected an overcurrent or short-circuit at the output, in the DC Link, or at the braking resistor. This can be due to a short-circuit between two motor phases, a short-circuit between the connection cables of the dynamic braking resistor, or shorted IGBT modules.
What does the F074 Ground Fault error mean on my WEG Inverter?
The WEG Inverter has detected a ground fault, which occurred either in the cable between the inverter and the motor or in the motor itself. This could be due to shorted wiring in one or more of the output phases or motor cable capacitance being too large, resulting in current peaks at the output.
What causes CPU Watchdog fault in WEG CFW-11 DC Drives?
A CPU Watchdog fault (F080) in WEG DC Drives is caused by electrical noise. Implement measures to reduce electrical noise.
What does the F076 Motor Current Imbalance fault mean on my WEG Inverter?
The WEG Inverter displays a motor current imbalance due to a fault. This can be caused by a loose connection or broken wiring between the motor and inverter connection, vector control with wrong orientation, or vector control with encoder, encoder wiring or encoder motor connection inverted.
What does Motor Current Imbalance mean in WEG DC Drives and how to fix it?
Motor Current Imbalance (F076) in WEG DC Drives indicates a loose connection or broken wiring between the motor and inverter connection. Check wiring between motor and inverter for issues.
What causes High Motor Temperature in WEG CFW-11 DC Drives?
High Motor Temperature (A110) in WEG DC Drives can result from excessive load at the motor shaft, an excessive duty cycle (too many starts/stops per minute), high surrounding air temperature, or a loose connection/short-circuit in the wiring connected to the motor termistor. Ensure optimal load conditions and check wiring.
What causes Motor Overtemperature in WEG DC Drives?
Motor Overtemperature (F078) in WEG DC Drives can be caused by: * Excessive load at the motor shaft. * Excessive duty cycle (too many starts / stops per minute). * High surrounding air temperature. * Loose connection or short-circuit in the wiring connected to the motor termistor. Ensure low loads and verify motor termistor installation to address this issue.
What causes High Load on Motor in WEG DC Drives and how to solve it?
A high load on the motor (A046) in WEG DC drives can occur if the settings of P0156, P0157, and P0158 are too low for the used motor, or if the motor shaft load is excessive. To solve this, adjust settings P0156, P0157, and P0158 as required.
General| Category | DC Drives |
|---|---|
| Model | CFW-11 |
| Power Range | 1.1-560 kW (1.5-750 hp) |
| Overload Capacity | 150% for 60 seconds |
| Braking | dynamic braking (optional) |
| Communication | Modbus RTU |
| Enclosure | IP20 |
Overview of HMI keypad functions, display, and parameter access.
Procedures for power, grounding, wiring, fuses, and control connections.
Details on installation, operation, wiring, and technical specifications of the Safety Stop function.
Steps to prepare the inverter before initial power-up.
Steps for initial inverter start-up, including password, oriented start-up, and parameter settings.
How faults and alarms are indicated and handled.
List of faults, alarms, and their likely causes.
Common problems and their corrective actions.
Electrical power specifications of the inverter.
To Next Page
