WEG CFW500 V1.8X User Manual

172 pages

To Next Page

Motors I Automation I Energy I Transmission & Distribution I Coatings

Frequency Inverter

CFW500 V1.8X

Programming Manual

Default Chapter5
- Table of Contents5
- Quick Reference of Parameters, Alarms and Faults9
Quick Reference of Parameters, Alarms and Faults10
1 Safety Instructions29
- Safety Warnings in this Manual29
- Safety Warnings in the Product29
- Preliminary Recommendations30
2 General Information31
- About the Manual31
- Terminology and Definitions31
3 About the Cfw50035
4 Hmi and Basic Programming39
- Use of the Hmi to Operate the Inverter39
- Indications on the Hmi Display39
- Operating Modes of the Hmi40
5 Programming Basic Instructions43
- Parameter Structure43
- Parameters Selected by the Hmi Menu43
- Hmi44
- Backup Parameters47
- Setting of Display Indications in the Monitoring Mode48
- Situations for Config Status48
- Softplc Engineering Units49
6 Identification of the Inverter Model and Accessories53
- Inverter Data53
7 Logical Command and Speed Reference57
- Selection for Logical Command and Speed Reference57
- Speed Reference63
- Control Word and Inverter Status68
  - Control Via HMI Inputs71
  - Control Via Digital Inputs72
8 Available Motor Control Types73
9 Scalar Control77
- PARAMETERIZATION of the V/F SCALAR CONTROL79
- START-UP in V/F MODE83
5 V W Vector Control85
- W Vector Control Parameterization87
- Start-Up in V V W Mode92
11 Functions Common to All the Control Modes95
- Ramps95
- DC Link Voltage and Output Current Limitation97
- DC Link Voltage Limitation by "Accelerate Ramp" P0150 = 1 or 398
- DC Link Voltage Limitation by "Ramp Hold" P0150 = 0 or 298
- Output Current Limitation by "Ramp Hold" P0150 = 2 or 3100
- Current Limitation Type "Decelerate Ramp" P0150 = 0 or 1100
- Sleep Mode101
- Flying Start / Ride-Through102
  - Flying Start Function103
  - Ride-Through Function103
- DC Braking104
- Avoided Frequency106
12 Digital and Analog Inputs and Outputs107
- Analog Inputs107
- Analog Outputs112
- Frequency Input115
- Frequency Output117
- Digital Inputs120
- Digital Outputs129
13 Pid Controller133
- Descriptions and Definitions133
- Start-Up135
- Monitoring Mode Screen138
- Sleep Mode with Pid138
- Pid Parameter139
- Academic Pid143
14 Rheostatic Braking145
15 Faults and Alarms147
- Motor Overload Protection (F0072 and A0046)147
- Igbts Overload Protection (F0048 and A0047)149
- Motor Overtemperature Protection (F0078)150
- Igbts Overtemperature Protection (F0051 and A0050)151
- Overcurrent Protection (F0070 and F0074)152
- Link Voltage Supervision (F0021 and F0022)152
- Plug-In Module Communication Fault (F0031)152
- W Control Mode Self-Tuning Fault (F0033)152
- Remote Hmi Communication Fault Alarm (A0750)152
- Remote Hmi Communication Error Fault (F0751)152
- Auto-Diagnosis Fault (F0084)152
- Fault in the Cpu (F0080)153
- Incompatible Main Software Version (F0151)153
- Pulse Feedback Fault (F0182)153
- Fault History153
- Fault Auto-Reset156
16 Reading Parameters157
17 Communication163
- Serial Usb, Rs-232 and Rs-485 Interface163
- Can - Canopen / Devicenet Interface165
- Profibus Dp Interface166
- Ethernet Interface167
- Commands and Communication Status169
18 Softplc171

Questions and Answers:

Need help?

Do you have a question about the WEG CFW500 V1.8X and is the answer not in the manual?

WEG CFW500 V1.8X Specifications

General

Category	DC Drives
Model	CFW500 V1.8X
Protection degree	IP20
Overload capacity	150% for 60s
Braking	Dynamic braking
Communication	Modbus RTU
Control Mode	Sensorless Vector
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short circuit
Communication Interface	RS485
Operating Temperature	-10 to 50 °C (14 to 122 °F)
Storage Temperature	-20°C to +65°C
Humidity	5 to 95% non-condensing
Switching frequency	4-16 kHz