Western 110 User Manual

20 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

October 1, 2018

Lit. No. 68660, Rev. 06

Western Products, PO Box 245038, Milwaukee, WI 53224-9538 • www.westernplows.com

This manual is for WESTERN

®

Model 110, 1000 & 2000 Low-Proﬁ le Tailgate Spreaders

with serial numbers 7192 and higher (Model 110), 10001–10002 (Model 1000), and 20237–20363 (Model 2000).

Low-Proﬁ le Tailgate Spreader

Model 110, 1000 & 2000

Owner's Manual

Original Instructions

This manual supersedes all editions with an earlier date.

CAUTION

Read this document before operating

or servicing the spreader.

Questions and Answers:

J
John TaylorJul 28, 2025
What to do if the Western 110 Spreader spinner does not spin and there is no power?
- M
  Mark AndersonJul 28, 2025
  If the spinner on your Western Spreader isn't spinning and there's no power, here's what you can check: * Ensure the spreader control is turned ON. * If using an ON/OFF control, check if the circuit breaker has tripped; if so, turn the control OFF, reset the breaker, and then turn the control ON. * Inspect the battery lead in-line fuse and replace it if blown, looking for any short circuits. * Check the battery connection for any issues; clean or replace the ring terminal and apply dielectric grease. * Examine the battery wiring harness for damage and repair or replace as needed.
R
Roy HowardAug 6, 2025
Why is the Western Spreader spinner not spinning when a load is applied, but the motor is turning?
- I
  Isaac JohnstonAug 6, 2025
  If your Western Spreader's spinner isn't spinning under a load, even though the motor is running, the issue might be with the drive belt or pulley. You should: * Remove the motor cap and check if the drive belt is broken or loose. Tighten or replace it as needed. * Also, remove the motor cap and make sure the motor and drive pulley set screws are tight.

Western 110 Specifications

General

Brand	Western
Model	110
Category	Spreader
Language	English

Summary

Preface

Owner's Information Form

Form to register spreader ownership details online and for manual reference.

Safety Information

Safety Definitions and Labels

Explains safety terms (Warning, Caution, Note) and describes warning/caution labels on the spreader.

Serial Number and Safety Precautions

Details the serial number format and provides essential safety precautions for operation and servicing.

Operational, Personal, and Fire Safety

Covers safe operating practices, personal protection, fire hazards, and cell phone use while operating.

Ventilation, Battery, and Noise/Vibration Safety

Addresses safety regarding vehicle exhaust, battery handling, noise exposure, and vibration levels.

Torque Chart Reference

Provides a chart with recommended torque values for various fastener sizes and grades.

Loading and Capacity Information

Vehicle Certification Requirements

Outlines National Highway Traffic Safety Administration certification for new vehicle installations.

Material Weights and Capacities

Details material densities (salt, sand) and spreader capacities for different models.

Mounting the Spreader

Fixed Mount Spreader Installation

Step-by-step instructions for mounting the spreader using the fixed mount system.

Swing Away Mount Spreader Installation

Step-by-step instructions for mounting the spreader using the Swing Away mount system.

Operating the Spreader

Spreader Control Operation

Details operation of the ON/OFF control and Variable Speed control for the spreader.

Starting and Stopping the Motor

Provides sequential steps for starting and stopping the spreader motor.

Driving and Spreading Safety Tips

Offers guidance and safety tips for driving and spreading materials in winter conditions.

Removing the Spreader

Fixed Mount Spreader Removal

Step-by-step instructions for safely removing the spreader from a fixed mount.

Swing Away Mount Spreader Removal

Step-by-step instructions for safely removing the spreader from a Swing Away mount.

Maintenance Procedures

Preseason Check

Essential checks and inspections before the ice control season begins.

After Each Use Cleaning

Procedures for cleaning the spreader after every use to prevent material issues.

Postseason Maintenance

Tasks required for storing the spreader during the off-season.

Drive Belt Replacement

Step-by-step instructions for replacing the drive belt.

Bearing, Fuse, and Recycle Procedures

Covers maintenance for bearings, fuse replacement, and disposal of used components.

2-PIN HARNESS WIRING DIAGRAM

TROUBLESHOOTING GUIDE

Related product manuals

Preview: Western tornado

Western tornado

Western ICE BREAKER

Preview: Western Striker Series

Western Striker Series