Whirlpool WCIC 3C26 PE

Questions and Answers

M
marcusmorrisAug 18, 2025
What to do if my Whirlpool WCIC 3C26 PE Dishwasher won’t start or respond to commands?
- S
  Stanley CurtisAug 18, 2025
  If your Whirlpool Dishwasher won't start or respond, there are several potential causes. First, ensure the appliance is properly plugged into the socket. If there was a power outage, the dishwasher will automatically restart when the power returns. Check that the dishwasher door is fully closed until you hear a 'click'. If it still doesn't respond, try switching the appliance off and on using the ON/OFF button, waiting about a minute before restarting.
D
Dawn MartinAug 20, 2025
Why my Whirlpool WCIC 3C26 PE Dishwasher won’t drain?
- R
  Robert LandryAug 20, 2025
  If your Whirlpool Dishwasher isn't draining, it could be due to several reasons. Ensure the wash cycle has completed. Inspect the drain hose to confirm it's not bent. Check the sink drain pipe for any blockages and clean it if necessary. Also, the filter might be clogged with food residues, so clean the filter.
M
Megan CooperAug 22, 2025
Why are the dishes not clean in my Whirlpool WCIC 3C26 PE?
- S
  sherri31Aug 22, 2025
  If your dishes aren't getting clean in your Whirlpool Dishwasher, consider these factors: make sure the crockery is arranged correctly so the spray arms can rotate freely. Select an appropriate wash cycle for the load. Ensure you're using the correct amount of detergent and that it's suitable for dishwashers. Verify that the rinse aid compartment cap is closed properly. Clean the filter assembly if it's soiled or clogged. Finally, check if the salt reservoir needs filling.
M
Morgan GonzalezAug 26, 2025
What to do if my Whirlpool Dishwasher won’t start?
- C
  cody74Aug 26, 2025
  If your Whirlpool Dishwasher isn’t starting or responding, here are a few things to check: * Ensure the appliance is properly plugged into the socket. * If there was a power outage, open the dishwasher door, press the START/Pause button, and close the door within 4 seconds, as the dishwasher doesn't restart automatically after a power interruption. * Make sure the dishwasher door is fully closed until you hear a 'click'. * If the door was opened for more than 4 seconds during a cycle, press START/Pause and close the door within 4 seconds. * If the display shows 9 or 12 and the On/Off LED is blinking rapidly, switch the appliance off and on again after one minute. If the problem continues, unplug the appliance for one minute, then plug it back in.
B
Brian GreeneAug 27, 2025
Why is my Whirlpool WCIC 3C26 PE not draining and showing error code 3?
- N
  nmartinezAug 28, 2025
  If your Whirlpool Dishwasher isn't draining and the display shows 3 with the On/Off LED blinking rapidly, here's what you can do: * Wait until the wash cycle finishes. * Check the drain hose to ensure it is not bent. * Clean the sink drain pipe if it is blocked. * Clean the filter if it's clogged with food residues.
M
Mary KellyAug 30, 2025
What to do if my Whirlpool WCIC 3C26 PE is not filling with water and displays H or 6?
- T
  Timothy RoachAug 30, 2025
  If your Whirlpool Dishwasher isn't filling with water and the display shows H, 6, and the On/Off LED is blinking rapidly, here’s what to check: * Ensure that there is water in the water supply and that the tap is open. * Make sure the inlet hose is not bent. * Clean the sieve in the water inlet hose if it is clogged. After cleaning, turn the dishwasher off and on, and restart a new program.
L
Lisa ChangSep 2, 2025
Why are my dishes not clean after using my Whirlpool Dishwasher?
- J
  Joe RobertsSep 2, 2025
  If your dishes aren't clean after a cycle in your Whirlpool Dishwasher, consider the following: * Ensure the crockery is arranged correctly so that water can reach all surfaces. * Check that the spray arms can rotate freely without being blocked by dishes. * Select a more appropriate wash cycle if the current one is too gentle. * Make sure you are using the correct amount of detergent and that it's suitable for dishwashers. * Verify that the cap on the rinse aid compartment is closed correctly. * Clean the filter assembly if it's soiled or clogged. * Fill the salt reservoir if it is empty.
Z
zhodgeSep 4, 2025
How to reduce excessive noise from my Whirlpool WCIC 3C26 PE Dishwasher?
- J
  Jeff DelgadoSep 4, 2025
  If your Whirlpool Dishwasher is making excessive noise, it could be that the dishes are rattling against each other; arrange the crockery correctly. Another cause could be an excessive amount of foam. This can be resolved by ensuring the detergent is measured out correctly and is suitable for dishwashers. Reset the dishwasher by pressing the DRAIN button and run a new program without detergent.
R
richardwilsonSep 7, 2025
How to fix excessive noise in my Whirlpool WCIC 3C26 PE?
- H
  hurstkimberlySep 7, 2025
  If your Whirlpool Dishwasher is making excessive noise, here are a couple of things to check: * Make sure dishes aren't rattling against each other by positioning the crockery correctly. * If there's an excessive amount of foam, it could be due to incorrect detergent dosage or unsuitable detergent. Restart the current cycle without adding any detergent by switching the dishwasher off, then on again, selecting a new program, pressing START/Pause, and closing the door within 4 seconds.
A
Ana WilliamsSep 9, 2025
Why is the salt indicator lit on my Whirlpool WCIC 3C26 PE Dishwasher?
- A
  Adam WellsSep 9, 2025
  The salt indicator on your Whirlpool Dishwasher may be lit because the salt reservoir is empty. Refill it with salt. Note that the indicator may remain lit for several wash cycles after refilling. Also, adjust the water hardness setting.

Whirlpool WCIC 3C26 PE Specifications

General

Control panel colour	Black
Number of Washing Programs	6
Delay Start	Yes
Half Load	Yes
Quick Wash	Yes
Appliance placement	Built-in
Number of Place Settings	14
Height	82 cm
Drying system	Condensation
Water consumption per cycle	9.5 L