Whirlpool WIC 3C34 PFE S User Manual (English)

Other manuals for Whirlpool WIC 3C34 PFE S

Questions and Answers:

G
Gerald BaileyAug 17, 2025
Why won't my Whirlpool WIC 3C34 PFE S start or respond to commands?
- T
  terricarrAug 17, 2025
  If your Whirlpool Dishwasher won't start or respond, ensure it's properly plugged into the socket. If there was a power outage, open the dishwasher door, press the START/Pause button, and close the door within 4 seconds. Also, check that the door is fully closed until you hear a 'click'. If the cycle was interrupted by opening the door for more than 4 seconds, press START/Pause and close the door within 4 seconds. If the display shows 9 or 12 and the On/Off LED is blinking rapidly, switch the appliance off and on again after one minute. If the problem continues, unplug it for 1 minute, then plug it back in.
P
Patricia SmithAug 20, 2025
What to do if my Whirlpool Dishwasher won’t drain and shows error code 3?
- S
  Shelby HaleAug 20, 2025
  If your Whirlpool Dishwasher isn't draining and the display shows 3 with the On/Off LED blinking rapidly, it could be due to several reasons. First, wait until the wash cycle finishes. Then, check that the drain hose isn't bent. Also, make sure the sink drain pipe is not blocked, and clean the filter if it's clogged with food residues.
C
Christian BarberAug 23, 2025
Why is my Whirlpool WIC 3C34 PFE S not filling with water and showing error H, 6?
- F
  Frank MarshallAug 23, 2025
  If your Whirlpool Dishwasher is not filling with water and displays H, 6 with the On/Off LED blinking rapidly, ensure that there is water in the water supply and that the tap is running. Also, check that the inlet hose is not bent. After verifying these, turn off and turn on the dishwasher and restart a new program. Finally, clean the sieve in the water inlet hose.
C
Christopher BlackburnAug 26, 2025
Why are the dishes not clean after using my Whirlpool Dishwasher?
- I
  Ian RayAug 26, 2025
  If the dishes in your Whirlpool Dishwasher aren't clean, ensure that the crockery has been arranged properly, allowing the spray arms to rotate freely. Select an appropriate wash cycle. Also, verify that the cap on the rinse aid compartment is closed correctly and that the filter is not soiled or clogged. Ensure that there is salt in the salt reservoir. If an excessive amount of foam has been produced, it means that the detergent has not been measured out correctly or it is not suitable for use in dishwashers.
A
Angela LopezAug 28, 2025
Why is my Whirlpool Dishwasher not working properly?
- D
  David MitchellAug 28, 2025
  Your Whirlpool Dishwasher might not be working because there is no water in the water supply, or the tap is closed. Ensure that there is water in the supply and the tap is open. Also, the inlet hose could be bent; make sure it is not. Another cause may be a clogged sieve in the water inlet hose; try cleaning it. If not, reprogram the dishwasher and reboot. After verification and cleaning, turn the dishwasher off and on, then restart a new program.
D
David Marshall IVAug 31, 2025
What to do if my Whirlpool WIC 3C34 PFE S doesn't work?
- C
  Carlos MasonAug 31, 2025
  If your Whirlpool Dishwasher isn't working, it could be due to several reasons. First, check if there's water in the water supply and that the tap is open. Second, inspect the inlet hose for any bends. Third, the sieve in the water inlet hose might be clogged, so clean it. If these steps don't resolve the issue, reprogram the dishwasher and reboot it. After checking and cleaning, turn the dishwasher off and on, and then start a new program.
T
Thomas YoungSep 3, 2025
How to fix a Whirlpool Dishwasher that is not working properly?
- J
  jonathan21Sep 3, 2025
  To fix a Whirlpool Dishwasher that isn't working, start by checking the water supply and ensuring the tap is open. Next, inspect the inlet hose for any bends. If the hose is fine, check the sieve in the water inlet hose for clogs and clean it if necessary. If the problem persists, try reprogramming and rebooting the dishwasher. After completing these checks and any necessary cleaning, turn the dishwasher off, then on again, and restart a new program.
A
Alan GarzaSep 5, 2025
How to reduce excessive noise from my Whirlpool Dishwasher?
- M
  Morgan RobertsonSep 5, 2025
  If your Whirlpool dishwasher is making excessive noise, it could be because the dishes are rattling against each other. Make sure to position the crockery correctly. Another reason could be an excessive amount of foam. If so, the detergent may not have been measured out correctly or is unsuitable for dishwashers. Restart the current cycle by switching the dishwasher off, then on again, select a new program, press START/Pause, and close the door within 4 seconds. Do not add any detergent during this restart.
C
Chris HensleySep 8, 2025
Why does my Whirlpool WIC 3C34 PFE S Dishwasher stop early and show error 15?
- A
  alangSep 8, 2025
  If your Whirlpool Dishwasher finishes the cycle prematurely and displays 15 with the On/Off LED blinking rapidly, check if the drain hose is positioned too low or siphoning into the home sewage system, ensuring the end of the drain hose is at the correct height. Additionally, check the water supply for leaks or other issues letting air inside.
S
Samuel KeithSep 12, 2025
How to turn off the salt indicator on my Whirlpool WIC 3C34 PFE S?
- S
  Stacy JonesSep 12, 2025
  The salt indicator on your Whirlpool Dishwasher may be lit because the salt reservoir is empty. Refill it with salt. Note that after refilling, the indicator may remain lit for several wash cycles. Also, adjust the water hardness according to the table provided.

Whirlpool WIC 3C34 PFE S Specifications

General

Door color	Silver
Cord length	1.3 m
Product size	Full size (60 cm)
Inlet hose length	1.55 m
Custom panel-ready	-
Outlet hose length	1.5 m
Appliance placement	Fully built-in
Baskets adjustable placement	Lower, Upper
Upper basket adjustable height	Yes
Cycle time	190 min
Noise level	44 dB
Delay start (max)	12 h
Dishwashing programs	Eco, Glass/delicate, Intensive 65°C, Pre-wash, Silent, Strong & Fast
Number of place settings	14 place settings
Number of washing programs	8
Current	10 A
Connected load	1900 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Energy efficiency scale	A to G
Water consumption per cycle	9.5 L
Package weight	37500 g

Weight and Dimensions

Depth	555 mm
Width	598 mm
Height	820 mm
Weight	35500 g
Installation compartment depth	560 mm
Installation compartment width	608 mm
Installation compartment height (max)	900 mm