Whirlpool WIO 3T133 PFE User Manual (English)

Questions and Answers:

F
francoashleyAug 12, 2025
What to do if my Whirlpool WIO 3T133 PFE won’t start or respond to commands?
- E
  emily25Aug 12, 2025
  If your Whirlpool Dishwasher won't start or respond, try these steps: * Ensure the appliance is properly plugged into the socket. * If there was a power outage, open the dishwasher door, press the START/Pause button, and close the door within 4 seconds. * Make sure the dishwasher door is fully closed until you hear a 'click'. * If the cycle was interrupted by opening the door for more than 4 seconds, press START/Pause and close the door within 4 seconds. * If the display shows 9 or 12 and the On/Off LED is blinking rapidly, switch the appliance off and on again after one minute. If the problem persists, unplug the appliance for 1 minute, then plug it back in.
P
paul27Aug 15, 2025
How to fix Whirlpool Dishwasher if the dishes are not clean?
- B
  Brian HarveyAug 15, 2025
  If your Whirlpool dishwasher leaves dishes unclean: * Ensure crockery is arranged correctly so that the spray arms can rotate freely. * Select an appropriate wash cycle. * Make sure that the cap on the rinse aid compartment is closed correctly. * Clean the filter assembly if it is soiled or clogged. * Fill the salt reservoir if it is empty. * Ensure the detergent has been measured out correctly and is suitable for dishwashers. If an excessive amount of foam has been produced, use the correct amount of detergent.
S
Shelley MccoyAug 19, 2025
What to do if my Whirlpool WIO 3T133 PFE won’t drain and shows error code 3?
- T
  todd56Aug 19, 2025
  If your Whirlpool Dishwasher won’t drain, and the display shows 3 with the On/Off LED blinking rapidly: * Wait until the wash cycle finishes. * Check the drain hose to ensure it is not bent. * Clean the sink drain pipe if it's blocked. * Clean the filter if it is clogged with food residues.
R
Richard BarrettAug 25, 2025
What to do if my Whirlpool WIO 3T133 PFE does not fill with water (Error H,6)?
- J
  Jody SteeleAug 25, 2025
  If your Whirlpool Dishwasher doesn't fill with water and the display shows H, 6, and the On/Off LED is blinking rapidly: * Ensure there is water in the water supply and that the tap is running. * Make sure the inlet hose is not bent. * Clean the sieve in the water inlet hose if it is clogged. After cleaning, turn the dishwasher off and on, then restart a new program.
L
Lisa RaymondAug 27, 2025
Why is the rinse aid indicator lit on my Whirlpool Dishwasher?
- M
  Mark GainesAug 27, 2025
  If the rinse aid indicator is lit on your Whirlpool Dishwasher, it means the rinse aid dispenser is empty. Refill the dispenser with rinse aid. Note that the indicator may remain lit for several wash cycles after refilling.
A
Allen PierceAug 31, 2025
How to turn off the salt indicator on my Whirlpool Dishwasher?
- A
  Adam StewartAug 31, 2025
  If the salt indicator is lit on your Whirlpool Dishwasher, it means the salt reservoir is empty. Refill the reservoir with salt and adjust water hardness. Note that the salt indicator may remain lit for several wash cycles after refilling.
R
Robert MerrittSep 3, 2025
Why is my Whirlpool WIO 3T133 PFE making excessive noise?
- P
  Patricia HerreraSep 4, 2025
  If your Whirlpool Dishwasher is making excessive noise: * Ensure the dishes are positioned correctly to avoid rattling. * If an excessive amount of foam has been produced, it means that the detergent has not been measured out correctly or it is not suitable for use in dishwashers. Restart the current cycle without adding any detergent by switching the dishwasher off, then on again, selecting a new program, pressing START/Pause and closing the door within 4 seconds.
C
Charles PhillipsSep 7, 2025
Why does my Whirlpool WIO 3T133 PFE Dishwasher stop mid cycle and show error 15?
- L
  laura78Sep 7, 2025
  If your Whirlpool Dishwasher finishes the cycle prematurely and displays 15 with the On/Off LED blinking rapidly: * Check if the end of the drain hose is placed at the correct height. * Check for siphoning into the home sewage system and install an air admittance valve if necessary. * Check the water supply for leaks or other issues letting air inside.

Whirlpool WIO 3T133 PFE Specifications

General

Energy Efficiency Class	D
Noise Level	43 dB
Water Consumption per Cycle	9.5 L
Energy Consumption per 100 cycles	85 kWh
Noise Emission Class	B
Number of programs	10
Control Type	Electronic
Display	Yes
Delay start	Yes
Half load	Yes
Number of Place Settings	14
Dimensions (HxWxD)	820 x 598 x 555 mm