Wholesale Interiors ADEN User Manual

STEP 1
STEP 2
STEP 3
STEP 4
ITEM : ADEN - FB/QB
ASSEMBLY INSTRUCTION
QTY
1PC
PART LIST
NO
HEADBOARD
CUSHION
RIGHT HEADBOARD LEG
WITH 'R' LABEL
WINGS
FOOTBOARD
CUSHION
FOOTBOARD
LEGS
SIDE RAIL
SIDE RAIL
SIDE RAIL
SUPPORT LEG
QTY
HARDWARE LIST
NO
SUPPORT LEGS
WITH ADJUSTABLE FEET
SLATS
JCBC SCREW
M6 X 70
JCBC SCREW
M6 X 35
JCBC SCREW
M6 X 25
JCBB SCREW
M8 X 20
L - KEY
M5 X 65mm
SCREW
M4 X 32mm
FLAT WASHER
SPRING WASHER
WOOD DOWEL
LEFT HEADBOARD LEG
WITH 'L' LABEL
L - KEY
M4 X 65mm
1PC
1PC
1PC
1PC
1PC
2PCS
2PCS
2PCS
2PCS
2PCS
2PCS
2PCS
4PCS
4PCS
8PCS
8PCS
8PCS
20PCS
20PCS
16PCS
1
2
3
4
5
6
7
8
9
9
10
11
Make sure the cleat is
on outside edge
Do not fully tighten screws
until assembly is complete
and the bed is level
Do not fully tighten screws
until assembly is complete
and the bed is level
Begin assembly by attaching each headboard leg (2) & (3) to the bottom
of headboard cushion (1) by aligning the hole and securing with 3
Allen bolts (C) , 3 spring washer (F) , 3 flat washer (G) per leg using
L-key (J).
Attaching each wing (4) to each side of headboard cushion (1) by
aligning the hole and securing with 3 Allen bolts (C) , 3 spring washer
(F) , 3 flat washer (G) per side using L-key (J).
Attach each footboard legs (6) to the bottom of the footboard cushion
(5) by inserting a dowel (E) & securing with 1 Allen bolt (D) per leg
using L-key (J).
Attach the side rail support leg (9) to the join of the side rail (7) &
side rail (8) by securing with 4 Allen bolts (B) , 4 spring washer (F) ,
4 flat washer (G) per support using L-key (J).

Wholesale Interiors ADEN Specifications

General

Brand	Wholesale Interiors
Model	ADEN
Category	Indoor Furnishing
Language	English

Summary

Assembly Steps - Initial Attachment

STEP 1: Headboard Leg Attachment

Attach headboard legs (2 & 3) to headboard cushion (1) with Allen bolts, spring washers, and flat washers.

STEP 2: Headboard Wing Attachment

Attach wings (4) to headboard cushion (1) using Allen bolts, spring washers, and flat washers.

STEP 3: Footboard Leg Attachment

Attach footboard legs (6) to footboard cushion (5) with dowels and Allen bolts.

STEP 4: Side Rail Support Attachment

Attach side rail support leg (9) to side rails (7 & 8) with Allen bolts, spring washers, and flat washers.

Assembly Steps - Final Assembly

STEP 5: Side Rail Attachment

Attach side rails (7 & 8) to headboard and footboard legs using Allen bolts.

STEP 6: Slat and Support Leg Attachment

Attach support legs (11) to slats (10) and slats to side rails.

STEP 7: Assembly Completion

Final check of all connections and tightening of bolts after assembly is complete.