What to do if the high pressure switch has shut down my Wine Guardian wine cooler?
If the high pressure switch has shut down your Wine Guardian wine cooler, it is likely that an obstruction is restricting airflow. Remove any obstructions in the duct or grille, or clean the filter. After that, restart the unit by resetting the high pressure switch.
Why is my Wine Guardian wine cooler leaking water?
If your Wine Guardian unit is leaking water, possible solutions include cleaning the trap, removing any blockages, and ensuring the unit is level using shims.
What to do if the cellar temperature is too high in my Wine Guardian, but the supply air is cold?
If the cellar temperature is too high, but the supply air is cold, you can try removing any blockage in the supply or return ductwork. Also, check and clean the filter and coil. As an additional measure, you can shut off the unit for two hours.
What should I do if the humidity is too high in my cellar and my Wine Guardian wine cooler is running but not cooling?
If the humidity is too high while your Wine Guardian unit is running but not cooling, try these steps: Check and reset the high limit switch. Clear any blockage of condenser airflow. Reduce the temperature or draw condenser air from another space.
How to fix a Wine Guardian wine cooler when the cellar temperature is too low while the unit is running?
If your cellar temperature is too low (below 51[0]) while the Wine Guardian unit is running, you can try the following: Reset the thermostat to a higher cooling temperature. Check for temperature rise across the coil. Reset the thermostat to a higher heating temperature. Replace the wiring.
What to do if my Wine Guardian wine cooler blows evaporator air, but the supply air isn't colder than the return air?
If your Wine Guardian unit is operating and blows evaporator air, but the supply air is not colder than the return air from the cellar, check the thermostat setup in the manufacture’s thermostat guide. You may also need to reset the HP switch.
Why is the humidity too high when my Wine Guardian wine cooler is running and cooling?
If the humidity is too high when your Wine Guardian unit is running and cooling, it may be due to poor vapor barrier installation. You can also refer to the Humidifier instructions or add a dehumidifier to the surrounding space.
What to do if humidity is too low in my cellar and my Wine Guardian wine cooler has an optional humidifier?
If the humidity is too low, and your Wine Guardian unit has an optional humidifier, check the wiring for loose, broken, or frayed connections. Also, check the humidistat setup, check for water flow and solenoid valve operation, and check the damper operation.
How do I fix a Wine Guardian wine cooler if the power switch light is off?
If the power switch light on your Wine Guardian wine cooler is off, first turn on the switch. If that doesn't work, check the circuit breaker and wiring. Also, make sure the unit is plugged in.
How to reduce noise from my Wine Guardian wine cooler when it's running?
If your Wine Guardian unit is running properly, but the sound is objectionable, try redirecting airflow, adding baffles, or adding insulated ductwork.
Procedure to register the warranty for a new Wine Guardian unit and accessories.
Details benefits of product registration, including safety notifications and proof of ownership.
Definitions for terms related to cellar conditions: Cellar, Condensate, Condenser, Evaporator, Set Point, Supply Air, Return Air.
Definitions for terms related to airflow and measurements: Ambient Air, BTU/H, CFM, SP.
Definitions for components and accessories: Flexible Duct, Grille or Diffuser.
Steps for carefully inspecting the unit upon arrival for any damage or discrepancies.
Verify the contents of the shipment against the packing slip for accuracy.
Specific items to check on the unit itself after unpacking, such as cords and lines.
Description of the unit's self-contained nature, sections, and primary functions.
Details how air from the cellar moves through the cooling coil, fan, and out.
Explains how ambient air circulates through the condenser section to reject heat.
Lists key internal components like expansion valve, filter dryer, and pressure switches.
Details on fan type, balance, lubrication, and motor requirements.
Information on exterior construction, coil materials, and access for maintenance.
Specifications for the digital thermostat and compressor type, including warranty.
Description of the optional built-in electric heating coil and its operation.
Details on the water-cooled condenser option using a heat exchanger.
Information on the ducting accessory kits, including sizing and installation.
Feature to enable operation in low ambient temperatures, controlling condenser fan speed.
Details on optional accessories for condensate removal and humidity control.
Description of the unit's cabinet, condensing section, and evaporator section.
Overview of electrical components, controls, and the washable air filters.
Details on the optional humidifier and the function of the internal drain trap.
Description of the refrigerant circuit components and supply/return grilles.
Illustration showing the physical layout of the unit's main components and airflow paths.
Diagram illustrating the refrigerant flow and components in the vapor compression system.
Detailed wiring diagram for the 115V Wine Guardian models.
Explanation of symbols, components, and connections used in the wiring diagrams.
Detailed wiring diagram for the 230V Wine Guardian models.
Explanation of symbols, components, and connections used in the wiring diagrams.
Table providing nominal dimensions and opening sizes for different unit models.
Data on unit weight and the refrigerant charge for various models.
Specifications for cooling capacity, compressor, controls, and accuracy.
Details on fan motor size, airflow, and heat capacity for both sections.
Information on power needs, current draw, and typical factory testing parameters.
Explanation of DANGER, WARNING, and CAUTION message conventions used in the manual.
Critical safety messages indicating imminently hazardous situations with high risk.
Safety messages indicating potentially hazardous situations with risk of injury or damage.
Safety messages indicating potentially hazardous situations with minor injury risk.
Procedure for safely de-energizing equipment before servicing.
Advice for qualified personnel regarding safe installation and operation practices.
Warnings about high voltage and the risk of electrical shock during operation or servicing.
Hazards associated with hot components and moving fan parts.
Information on the lack of electrical safety lockouts and required power disconnection.
Details on the main power switch's location and how it shuts off power.
Warnings regarding electrical hazards, rigging, and unit support structures.
Precautions for cleaning the unit and avoiding water contact.
Guidance on protecting the power cord and ensuring proper grounding.
Conditions under which servicing by qualified personnel is required.
Steps to test the unit for non-visible shipping damage before installation.
Diagram illustrating the airflow paths for the evaporator and condenser sections.
Safety warnings regarding unit weight, modifications, and prohibited actions.
Requirements for electrical outlets and dedicated circuits for unit models.
Key considerations for planning the unit's location, mounting, and connections.
Steps to verify electrical configuration, breaker size, and installation site.
Guidelines for positioning the unit and recommended ductwork lengths.
Instructions for installing grilles and relocating them for ductwork.
Methods to minimize operational noise through unit placement and sound baffling.
Requirements for protecting the unit if installed outdoors in an enclosure.
Details on floor, wall, and ceiling mounting procedures and support requirements.
Structural requirements for securely mounting the unit to ceiling joists.
Instructions for connecting the drain line and ensuring proper drainage.
Explanation of how the internal drain trap primes automatically.
Guidelines for connecting the unit to the electrical power supply safely.
Details found on the unit's serial plate, including model and electrical specifications.
Illustrations of required electrical plug types for different unit models.
Instructions for connecting the thermostat and its wiring to the unit.
Steps for removing, reinstalling, and adding wiring to the thermostat.
Guidelines for selecting an optimal location to mount the thermostat.
Information on factory settings and adjusting the thermostat for temperature control.
Notes on thermostat setup numbers and factory settings.
Explanation of thermostat time delays designed to prevent short-cycling.
Guidance on positioning grilles for optimal airflow and circulation.
Procedure for removing and relocating the unit's grilles.
Chart providing recommended duct sizes for evaporator and condenser sections.
Important warnings regarding crimping flexible ducts and insulation requirements.
Guidelines for supporting, stretching, and connecting flexible ductwork.
Instructions for situations where ductwork is not utilized.
Connecting ductwork for supply and return air between the unit and the cellar.
Using ductwork to direct condenser heat and noise away from occupants.
Illustrations and descriptions of different through-wall mounting configurations.
Illustrations of remote floor mounting and various ceiling mounting options.
Illustrations of outside through-wall and remote mounting configurations.
Table detailing duct adapter dimensions for various unit sizes and locations.
Diagram and explanation for a single outlet duct connection setup.
Diagram and explanation for a dual outlet duct connection setup.
Checklist for verifying unit condition and completeness upon receipt.
Checklist for ensuring proper unit mounting, service, and accessory installation.
Checklist for final checks before and during unit startup.
Procedure for powering on the unit and initial checks.
Steps to test the evaporator fan operation using the thermostat.
Initial operation guidelines, including compressor confirmation and noise checks.
Explanation of normal fan and condenser fan cycling behavior.
Recommended thermostat settings for optimal cellar temperature control.
Tips for maintaining consistent temperature using airflow and thermostat settings.
Instructions for rotating grilles and balancing airflow in ductwork.
Safety warnings and general advice before performing any maintenance tasks.
Step-by-step guide for cleaning the reusable evaporator and condenser air filters.
Instructions for cleaning the condensate drain system annually.
Guidance for periodic maintenance of the optional humidifier.
Information on the heating coil's location, operation, and testing.
Explanation of the low ambient option's purpose and operational behavior.
Routine checks for filters, drain traps, noise, and short-cycling.
Annual tasks including filter replacement and coil cleaning.
Procedure for flushing and cleaning the condensate pan under the evaporator coil.
Inspecting the cabinet for corrosion and cleaning the unit's interior.
Table identifying common causes and solutions for start-up issues.
Solutions for issues where the unit fails to power on or the thermostat is off.
Diagnosing why supply air is not colder than return air, checking compressor and airflow.
Causes and solutions for the cellar temperature being too low.
Causes and solutions for the cellar temperature being too cold when the unit is not running.
Causes and solutions for the cellar temperature being too high with cold supply air.
Diagnosing and resolving low humidity issues with or without the optional humidifier.
Diagnosing and resolving high humidity issues during or after cooling cycles.
Troubleshooting when the unit is running but the power switch indicator is not illuminated.
Causes and solutions for water leaks, including trap and pan issues.
Identifying and resolving unusual noises originating from the unit or airflow.
Understanding why the high pressure switch trips and causes shutdowns.
Step-by-step guide on how to reset the manual high pressure switch.
Diagnosing and resolving issues causing the evaporator coil to freeze.
Troubleshooting frequent tripping of the high pressure switch.
Diagnosing causes for the unit cycling on and off more than 8 times per hour.
Troubleshooting high-pitched, loud rubbing, clanking, or vibration noises.
Procedure and considerations for replacing fan motors or impeller wheels.
Steps to follow for warranty claims, including authorization and part returns.
Terms and duration of the warranty for defects in material and workmanship.
Exclusions and limitations on warranty claims, including consequential damages.
Purchaser's agreement to indemnify and waiver of sovereign immunity.
Requirements for obtaining authorization and returning defective parts.
General| Brand | Wine Guardian |
|---|---|
| Model | 24S088 |
| Category | Wine Cooler |
| Language | English |
To Next Page