Wood-mizer LT15W User Manual (English)

Other manuals for Wood-mizer LT15W

Safety, Operation, Maintenance & Parts Manual17 pages

Questions and Answers:

J
Jenna SmithSep 1, 2025
Why is my Wood-mizer LT15W Saw lumber not square?
- M
  Maureen LaneSep 1, 2025
  If the lumber from your Wood-mizer Saw is not square, several factors could be the cause. Check if the vertical side supports are not square to the bed and adjust them. Ensure the blade is parallel to the bed rails, adjusting the bed rails if needed. Also, remove any sawdust or bark between the cant and bed rails. Finally, tooth set problems can cause this issue, so resharpen and reset the blade.
J
Joseph WalshAug 31, 2025
Why do Wood-mizer LT15W blades dull quickly?
- T
  Tanya PrinceAug 31, 2025
  Your Wood-mizer Saw blades may be dulling quickly due to several factors. The logs might be dirty, so clean or debark them, especially on the entry side of the cut. If you are grinding teeth, you might be heating them too much, causing them to soften; grind just enough metal to restore sharpness and use water/coolant while sharpening. Poor sharpening techniques can also be a factor, so carefully read the instructions with your blade sharpening equipment to ensure the tip is being sharpened completely.
K
kevin68Aug 29, 2025
Why do I get wavy cuts with my Wood-mizer LT15W?
- J
  Jessica ToddAug 29, 2025
  Wavy cuts can occur due to several reasons. You might be feeding the saw too quickly, so try slowing down the feed rate. The blade might be improperly sharpened, so resharpen it carefully, following the sharpener’s instructions. Check if the blade guides are improperly adjusted and adjust them accordingly. Sap buildup on the blade can also cause this, so consider using Water Lube. Finally, a tooth set problem can be the cause, so resharpen and reset the blade.
A
Ashley WangAug 27, 2025
What causes drive belts to wear prematurely or jump on a Wood-mizer LT15W?
- M
  Matthew HodgesAug 27, 2025
  If the drive belts are wearing out quickly or jumping, it's likely due to the engine/motor drive pulleys being out of alignment. Make sure to align the pulleys.
N
nicholasfoxAug 27, 2025
How to correct Lumber that is not square with my Wood-mizer LT15W Saw?
- S
  Scott YangAug 27, 2025
  If your lumber isn't square, it could be due to several reasons. Start by adjusting the side supports to ensure they are square to the bed. Next, adjust the bed rails so they are parallel to the blade. Make sure to remove any sawdust or bark between the cant and bed rails. Finally, resharpen and reset the blade to address any tooth set problems.
K
Kimberly JonesAug 25, 2025
What to do if the blade does not track right on the drive wheel of my Wood-mizer Saw?
- D
  Dr. Laura RileyAug 26, 2025
  If the blade on your Wood-mizer Saw isn't tracking correctly on the drive wheel, the cant adjustment is likely incorrect. Readjust it.
T
Troy PriceAug 23, 2025
Why do drive belts wear prematurely or jump on my Wood-mizer Saw?
- C
  Christopher NguyenAug 23, 2025
  If the drive belts on your Wood-mizer Saw are wearing out quickly or jumping, it's likely that the engine/motor and drive pulleys are out of alignment. You should align the pulleys.

Wood-mizer LT15W Specifications

General

Engine	Gasoline or Electric
Engine Power	14 HP (10.4 kW) or 7 HP (5.2 kW)
Max Log Diameter	72 cm
Max Width of Cut	64 cm
Max Cant Width	26 inches
Blade Width	1.5 inches
Blade Thickness	0.042 inches