What to do if my Worx LANDROID WR210 Lawn Mower Landroid Vision can not find the charging base?
If your Worx Landroid Vision can't find the charging base, ensure it docks right towards the charging base and departs in an anti-clockwise direction. Also, remove any obstacles within 2 meters in front of the charging base.
Why is my Worx LANDROID WR210 grass being cut unevenly?
Uneven grass cutting by your Worx Lawn Mower may occur due to several reasons: * The mower isn't working enough hours daily – try adding more hours to the mowing schedule. * The mowing area is too large – decrease the mowing area size or increase working time. * The blades are dull – change all blades and screws to balance the blade disc. * The cutting height is too low – raise the cutting height gradually. * Grass is wrapped around the blade disc – check and remove any obstructions. * There's a buildup of grass in the blade disc or motor frame – ensure the blade disc rotates freely, removing debris if needed. * Recognition error - remove the obstacles, such as leaves.
Why does my Worx LANDROID WR210 Lawn Mower Landroid Vision turns on, but the blade disc does not spin?
This is normal behavior for your Worx Lawn Mower Landroid Vision. When Landroid Vision needs to recharge, the blade disc does not rotate while it is searching for the charging base automatically.
What to do if my Worx LANDROID WR210 Lawn Mower Landroid Vision slips out of its working area?
If your Worx Landroid Vision slips out of its working area: * Check that the wheels are clean and free of mud to ensure maximum grip. * Exclude slopes steeper than 30% by using a magnetic strip or a non-grass pathway. * Remove any obstacles causing recognition errors and ensure correct mower function with a magnetic strip or non-grass pathway on the lawn edge.
What to do if my Worx LANDROID WR210 Landroid Vision operative system crashes when charging or on standby?
If your Worx Landroid Vision operative system crashes, restart Landroid Vision. This may resolve software or display faults.
What to do if my Worx LANDROID WR210 Lawn Mower Landroid Vision stops in the working area?
If your Worx Landroid Vision stops in the working area, it may be due to: * An obstacle in the working area – remove the obstacle. * The cutting height being too low or the grass being too dense – raise the cutting height gradually.
What to do if my Worx Lawn Mower Landroid Vision shuts off when docking in the charging pile?
If your Worx Landroid Vision shuts off when docking, it may be due to: * Over temperature protection – place the charging base in a shady area or wait for cooler temperatures. * Poor connection – check the LED light on the charging pile and the connection between the contact pins on the charging pile and the charging strip.
What to do if my Worx LANDROID WR210 Landroid Vision cannot correctly dock with the charging pile?
If your Worx Landroid Vision cannot correctly dock with the charging pile, try the following: * Restart Landroid Vision due to potential environmental influences. * Clean the contact pins on the charging pile and the charging strip on Landroid Vision with a cloth due to poor connection caused by debris. * Ensure the QR code is clear and unobstructed.
What to do if my Worx LANDROID WR210 Landroid Vision is starting to have shorter run-times between charges?
Shorter run-times between charges for your Worx Landroid Vision can be caused by: 1. Clogging in the blade disc – take off the blade disc and clean it, especially if the grass is high or thick. 2. Unbalanced blade disc – check the blade disc and blades, remove debris, and replace blades if needed. 3. Exhausted or old battery – replace the battery. 4. Working time is up - reset the working time.
What to do if my Worx LANDROID WR210 Lawn Mower is not charging?
If your Worx Lawn Mower is not charging, check that the power cord is properly connected to the charger and the charger to a suitable power supply. Also, ensure both charging strips on the mower touch the center of the charging contacts on the charging pile.
General| Cutting Width | 22 cm |
|---|---|
| Battery Voltage | 20 V |
| Battery Capacity | 2.0 Ah |
| Max Lawn Size | 1000 m² |
| Slope Capability | 35% |
| Smart Navigation | Yes |
| Rain Sensor | Yes |
| Slope Handling | 35% |
| Noise Level | 60 dB |
| Operating Time | 60 minutes |
| Anti-Theft System | PIN code |
Read and understand instructions, be familiar with controls, and know proper appliance use.
Ensure correct installation of the automatic perimeter delineation system using the camera.
Covers general operation guidelines, including safety devices and handling.
Details on switching off the mower for maintenance and storage procedures.
Important safety precautions regarding battery handling, charging, and disposal.
Explains the Al camera technology and operational features of the Landroid Vision.
Explains PIN code protection and auto-lock function for unauthorized access.
Instructions on how to start the Landroid Vision mower and update its software.
Details on configuring advanced settings via the built-in interface or the Landroid Vision app.
Instructions on blade maintenance, checking for damage, and replacement.
Lists common error messages, their causes, and suggested solutions.
A guide to diagnose and resolve common issues encountered with the Landroid Vision.
To Next Page