12
• For optimal battery life and performance the
battery should be fully charged after each use
• Store the battery in a cool dry location.
• The battery can be safely stored down to 14°F
(-10°C).
• The battery does not need to be fully discharged
before recharging.
• Initially 2 to 3 charging cycles may be required
after purchase to achieve the maximum run time
capacity.
The battery is maintenance free and requires no
service. ADDITIONAL BATTERIES can be obtained
from the Customer Helpline 1-866-354-9679.
ASSEMBLY
IMPORTANT! Before you assemble the lawn
mower, check the accessories according to the
above information, make sure the accessories are
included and functional.
1.FITTING THE HANDLE BAR (See Fig. B1-B4)
1) Remove the screws (a) on both sides of the deck
(See Fig. B1) .
2) Insert the Lower Handle Bar (10) into the holes
on the deck. Be sure to carefully align the screw
holes found on the Lower Handles with the
screws holes found on the deck (a). (See Fig. B1
B2)
3) Secure the Lower Handle Bars to the deck with
the screws provided (See Fig B2) .
4) Attach the Middle Handle (9) to the Lower Handle
with the bolts and Lower Handle knobs (8). After
this is complete, attach the Upper Handle (1)
to the Middle Handle with the bolts and upper
Handle knobs (7) (See Fig. B3).
5) Tightening the Handle Knobs(7/8). Check that the
handles are FULLY secured.
6) First, insert the cable into the Cable Clips (3)
provided ensuring there is enough slack cable
to allow the handlebars to collapse for storage.
After inserting the cable, attach the Cable Clips to
the Upper and Middle Handle bars (See Fig. B4).
NOTE: Make sure the cable is routed underneath
the Middle Handle Bar (See Fig.B4).
2. GRASS COLLECTION BAG ASSEMBLY
1) Attach the Grass Collection Bag handle to the
grass bag assembly as shown in Fig C1-C4.
a. Identify the front and rear of both the handle
and the Grass Collection Bag(5) assembly (See
Fig. C1).
b. Insert the front portion of the handle into
position (See Fig. C2).
c. Secure the front portion of the handle in place
by pushing it forward (See Fig. C2).
d. Insert and secure the rear portion of the handle
in position by pushing down on the back of the
handle. Ensure that “clicks” into position (See
Fig. C2) .
2) Clip the plastic clips of the Grass Collection Bag
over the metal frame (See Fig. C3) .
WARNING: Make sure to not fit the handle
in the reverse direction as it will not
remain secure. Make sure to fit the handle as
shown in Fig C4.
3. ATTACHING THE GRASS BAG TO THE
MOWER (See Fig. D1, D2, D3)
NOTE: The grass bag is held in place by the
Safety Flap.
1. Switch the mower off, remove the Safety Key (6)
and wait until the mower Blade (17) has stopped.
2. Raise the Safety Flap (11) and hold it in the
upward position while the Grass Collection Bag
(5) is properly located below it (See Fig. D1).
3. Position the lower edge of the Grass Collection
Bag on the plastic tabs (b) found below the rear
discharge chute on the mower deck. (See Fig.
D2).
4. While holding the Grass Collection Bag in
position lower the safety flap into its’ final
position. It should rest on top of the grass bag
with the tabs of the Grass Collection Bag being
inserted into the Safety Flap. Ensure the Safety
Flap locks securely into position with the Grass
Collection Bag (See Fig. D3) .
NOTE: The two parts should smoothly slide
together with little force. They WILL NOT “click”
together.
NOTE: Press down on the Grass Collection Bag
slightly to ensure that it is completely installed.
4. REMOVING/EMPTYING THE GRASS
COLLECTION BAG
1) Switch the mower off, remove the Safety Key (6)
and wait until the mower blade has stopped.
2) Hold the grass bag handle.
3) Raise the Safety Flap (11) upward and hold it in
the upward position until the Grass Collection
Bag is removed (See Fig. D1).
WARNING! Before each use, always check that
the safety flap closes securely over the rear
discharge chute. Never lift the Safety Flap when the
lawn mower is in operation. The Blade(17) must be
completely at rest before handling the safety flap.
5. FITTING/REMOVING THE BATTERY PACK
(See Fig. E1, E2, E3, E4)
REMOVING BATTERY PACK (12)
1) While gripping the battery handle lift it upward
without twisting or turning it (See Fig. E1) .
FITTING BATTERY PACK
1)
Locate the front and rear of the battery (See Fig. E2).
2)
Lower the battery into position. (See Fig. E3).
NOTE: For a secure fit, make sure the
battery tray is free of debris and the
contacts on the battery and in the battery
tray are clean (use a dry cloth to clean)
(See Fig. E4).
NOTE: When fitting or removing the battery be
careful not to drop the battery onto your foot or the
ground.
To Next Page
Loading...
Need help?
General
