XtremepowerUS 90151 - User Manual

Questions and Answers

B
bennettdorothyAug 2, 2025
What to do if my XtremepowerUS 90151 Swimming Pool Filter shows 'NO FLOW'?
- C
  caroline21Aug 2, 2025
  If the XtremepowerUS Swimming Pool Filter displays 'NO FLOW', ensure the filter pump is operating and there are no obstructions in the piping. Increase the flow of the filter pump and expel air from the cells, ensuring the water surface exceeds 2/3 of the cells. Also, check if the filter is in backwash status and adjust accordingly. If the issue persists, the flow switch circuit may be disconnected or faulty, requiring replacement of the flow switch.
H
Hannah RobertsAug 6, 2025
What to do if XtremepowerUS 90151 shows Err5 and the Water Temperature light is on?
- D
  David ThomasAug 6, 2025
  If your XtremepowerUS Swimming Pool Filter displays 'Err5' and the Water Temperature light is on, it means the detected water temperature has exceeded 113°F (45°C). The system will resume operation when the water temperature is between 55°F (13°C) and 109°F (43°C). Ensure the water temperature recovers and restart the chlorine generator. Also, check whether the flow switch circuit is broken.
C
Cindy FreemanAug 11, 2025
Why does the LED display screen of my XtremepowerUS Swimming Pool Filter not display?
- K
  klinelucasAug 11, 2025
  If the XtremepowerUS Swimming Pool Filter LED display screen does not display, check that the power cord of the control box is plugged into a protected socket and make sure that the chlorine generator is working properly. If it is still not working, the chlorine generator controller box may need to be replaced.
F
Frederick PerezAug 15, 2025
What to do if XtremepowerUS Swimming Pool Filter displays Err2 Load break?
- S
  Shawna MaynardAug 15, 2025
  If your XtremepowerUS Swimming Pool Filter shows 'Err2 Load break', it could be due to very low salinity, a disconnected wire to the titanium plate, or an old titanium plate. Add a small amount of salt water to the cells and restart the chlorine generator. Cut off the power supply, remove the chlorine generator, and check whether the titanium plate wiring is off. If the titanium plate is very old, change electrolytic cell.
K
Kelly JonesAug 19, 2025
What to do if XtremepowerUS Swimming Pool Filter displays Err1 Load short circuit?
- K
  Karen MillerSep 12, 2025
  If your XtremepowerUS Swimming Pool Filter displays 'Err1 Load short circuit', it could be due to a conductive metal embedded in the titanium plates or a short circuit of water inlet at the connection of titanium plates. Cut off the power supply, remove the chlorine generator and rinse the titanium plate. Also, check whether the wiring position of the titanium plate is flooded or burnt out. If not drain out of water, re-install and start the equipment.
D
Dr. Joseph Benton MDAug 25, 2025
What to do if XtremepowerUS Swimming Pool Filter displays Err4?
- T
  Timothy FosterAug 25, 2025
  If your XtremepowerUS Swimming Pool Filter displays 'Err4', it indicates that the salinity is lower than the specified limit. You should expel air from the cells, ensuring that the water surface exceeds 2/3 of the cells. Additionally, add salt to the pool.
G
George MccartyAug 27, 2025
What to do if XtremepowerUS 90151 displays Err3?
- D
  Diana EllisonAug 28, 2025
  If your XtremepowerUS Swimming Pool Filter displays 'Err3', it means the salinity is higher than the maximum limit specified. To resolve this, change part of the pool water to reduce salinity.

Summary

Important Safety Information

General Safety Warnings

Read all safety warnings and instructions for potential injury or death.

Safety Precautions

General safety precautions, common sense, and understanding instructions for safe operation.

Product Information

General Instruction

Explains the function of the chlorine generator for pool sanitation.

Operational Parameters

Details temperature, water flow, and salinity ranges for optimal generator performance.

Safety Warnings

Warning and Safety Instructions

Critical warnings for electrical hazards and safe appliance usage.

Operation

Function and Operation Modes

Details super chlorination, original chlorination, and automatic cleaning modes.

Control Panel Overview

Overview of the control panel, indicators, and display.

Button Functionality

Explains the function of each button on the control panel for operation.

LED Display Screen Meanings

Explains the meaning of different display characters shown on the LED screen.

Daily Usage and Maintenance

Provides guidance on daily usage and maintenance procedures for the system.

Salinity Regulation

Details how to manage and regulate the salt level in the pool water.

Salt Addition Guidelines

Guidelines for salt addition, types, and quantities based on pool volume.

Antifreeze Precautions

Advice on preventing damage from freezing conditions to the generator.

Electrolytic Cell Maintenance

Instructions for maintaining and cleaning the electrolytic cell and replacing the flow switch.

Troubleshooting

Error Code Resolution

Lists error codes, reasons, and troubleshooting steps for system issues.

Specifications

Technical Parameter Table

A table detailing the technical specifications for different product models.

Disclaimer

Important Notices

Important disclaimer regarding repairs, warranties, and serial number recording.

XtremepowerUS 90151 Specifications

General

Brand	XtremepowerUS
Model	90151
Type	Sand Filter
Hose Connection	1.5 inches
Filter Media	Sand
Tank Material	Polyethylene
Working Pressure	50 PSI
Inlet/Outlet Size	1.5 inches
Sand Capacity	42 lbs
Valve Type	Multiport